Process Equipment & Plant Design Mcqs for Chemical

Q.  Wind load consideration in the design of a support can be neglected, when the vessel is___________________?

a. Tall (say 30 metres), but is full of liquid
b. Tall but empty
c. Short (< 2 m) and housed indoor
d. None of these


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  The minimum shell thickness for tank ≤ 15 metres diameter is limited to _______________ mm, for reasons of elastic stability?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  _____________ shaped roof is the most commonly used roof for cylindrical storage tanks?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Filtration rate is affected by the________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Normally, the length to diameter ratio of rotary dryers varies from 4 to 10 and for its economic operation; the number of transfer units (NTU) for such dryers varies from ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick out the wrong statement ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of volumes of the mixed reactor to the plug flow reactor (for identical feed composition, flow rate, conversion, and for all positive reaction orders) is always ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a _____________ riveted joint, the number of rivets decreases from the innermost row to the outermost row?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A binary liquid Azeotropic mixture has boiling point lower than either of the components, when it shows _____________ deviation from Raoult’s Law?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The clearance between two tubes in a shell and tube heat exchanger is known as ‘ligament’, whose minimum value is _____________ the outside diameter of the tube, but in no case it should be less than 4.5 mm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following is the most common type of baffle used in industrial shell and tube heat exchanger ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  ____________ is the determining factor for the number of bubble caps to be used per tray?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The buckling tendency of compression members is always in the direction of the _____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The equivalent diameter for fluid flow through a channel of constant non-circular cross section of area ‘A’ is given by (where, P = perimeter of the channel in contact with the fluid) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Accidents in chemical plants are mostly due to___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Liquid redistribution should be done in a packed tower packed with raschig rings every 6 metres or ______________ times the column diameter, whichever is lower?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of linear stress to linear strain is termed as the ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A perforated plate has holes of diameter dn arranged in a pitch ph. Each hole has a tube of I.D. dt passing through it. The ligament efficiency is given by_______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The thermal stress in a metallic bar does not depend upon the_____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Diameter of rivet hole (d, mm) and the plate thickness (t, mm) are related by Unwin’s formula as___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Steam is preferred to be used as a heating medium in heat exchangers, because of its_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts