|
MCQs: For earthquake resistant masonry buildings, where seismic coefficient is less than 0.08, the horizontal distance between two openings shall not be less than_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Assertion A : Lime based mortars give higher ratio of brickwork strength to mortar strength as compared to non-lime mortar. Reason R : Lime based mortars have lower bond strength as compared to non-lime mortars?
Select your answer according to the codes given below.
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Minimum thickness of stiffening wall for 1 to 3 storeys shall not be less than_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Assertion A : From consideration of structural soundness and economy of design, most codes control the maximum slenderness ratio of masonry walls and columns. Reason R : By controlling the maximum slenderness ratio, failure is by excessive stress and not by buckling.?
Select your answer according to codes given below.
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: For designing masonry components of a structure, seismic forces provision in the design calculation is not necessary for buildings constructed in________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Full restraint is provided by__________________?
i) foundation footing of a wall
ii) timber floor spanning on the wall and anchored to the wall
iii) RCC slab with a minimum bearing of 10 cm on the wall
select the correct statment.
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The bending stress in a wall or column subjected to effective vertical load need not be considered, if the eccentricity ratio is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If the horizontal cross-sectional area of a wall is 1200 cm2, then the basic stress shall be multiplied by a reduction factor equal to________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If H is the height of wall between centers of supports, then the effective height of wall where concrete floors have a bearing on wall irrespective of the direction of span will be________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Where a structural component or a system is providing lateral support to five or more walls or columns, the lateral load to be resisted may be taken as_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If the ratio of center to center spacing of intersecting walls to actual thickness of intersecting wall is more than 20, then the stiffening coefficient for wall proper will be_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Assertion A : For eccentricity ratio exceeding 1/6, effective thickness of masonry will get reduced. Reason R : For eccentricity ratio exceeding 1/6, there will be tension on one side of the member?
Select your answer according to the codes give below.
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Maximum slenderness ratio of load bearing walls for a dwelling having more than 2 storeys________________?
i) shall not exceed 12 if lime mortar is used
ii) shall not exceed 18 if cement lime mortar 1:2:9 is used
iii) shall not exceed 24 if cement mortar 1:6 is used
the correct statments is ?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Consider the following statements?
1. Masonry in rich cement mortar though having good strength with high shrinkage is much liable for surface cracks.
2. Lime mortar possesses poor workability and poor water retentivity and also suffers high shrinkage.
3. Masonry in lime mortar has better resistance against rain penetration and is less liable to crack when compared to masonry in cement mortar.
Which of these statements are correct?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A good blast with a good yield is obtained if the cut hole is___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Drifters can be used to drill_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The correct sequence of drilling equipment for increasing size of holes in tunnels is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: In compressed air tunneling, the volume of free air provided is______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Which of the following lining material is useful for shield driven tunnels in sub aqueous regions ?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Which one of the following tunnelling methods is used for laying under ground sewers ?
Category: Civil Engineering Mcqs, Published by: teswesm
|
