Process Control & Instrumentation Mcqs for Chemical


Q.  Which of the following thermocouples is the most suitable for measuring a temperature of about 1600°C in an oxidizing atmosphere ?

a. Platinum-platinum + rhodium
b. Iron-constantan
c. Copper-constantan
d. Chromel-alumel


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Continuous shell temperature measurement in a liquid-liquid heat exchanger is done by a __________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  What is the ratio of output amplitude to input amplitude for a sinusoidal forcing function in a first order system ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Flow rate through an orifice is _____________ the pressure differential?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Which of the following is not the triple point of water ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Measurement of sub-zero Celsius temperature in industry is done most commonly by __________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Characteristic equation is the denominator of ____________ loop transfer function?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Smoke density of the flue gas going out of the chimney is measured by a __________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The experimental response of the controlled variable y(t) for a step change of magnitude ‘P’ in the manipulated variable x(t) is shown below: The appropriate transfer function of the process is_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Mercury manometer (U-tube type) exemplifies a ______________ order system?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Liquid argon level in a pressurised storage tank (at 3 kg/cm2) is measured by a/an ____________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  E.m.f. generated by thermocouples is of the order of ________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The frequency response of a dynamic element shows a constant magnitude ratio at all frequencies. The element exhibits a negative phase shift at all frequencies. The absolute value of the phase shift increases linearly with frequency. The element has the transfer function ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Paramagnetism method is not used for the composition determination of ______________ in gases?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Suppose that the gain, time constant and dead time of a process with the following transfer function: Gc(s) = 10 exp( – 0.1s)/(0.5s + 1) are known with a possible error of ± 20% of their values. The largest permissible gain Kc of a proportional controller needs to be calculated below taking the values of process gain, time constant and dead time as________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Transfer function of transportation lag is___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  An amplitude ratio of 0.1 corresponds to _____________ decibels?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Emf developed by a thermocouple while measuring a temperature of 400°C is 22 mV. The type of thermocouple used is ___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  What is the dynamic error in a critically damped second order instrument for a ramp input (At) ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Which of the systems having the following transfer function is stable ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Which of the following fluid flow measuring devices can measure the largest flow rate ?
Category: Chemical Engineering Mcqs,   Published by: teswesm