Chemical Engineering Basics Mcqs

Q.  Which of the following terminology is used for the temperature at which new grains are formed in a metal ?

a. Eutectic temperature
b. Lower critical temperature
c. Recrystallisation temperature
d. Upper critical temperature


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  Electrolytic reduction cell used for conversion of calcined Al2O3 to Al is a carbon lined furnace operating at 800-900 °C. The purpose of electric current supplied to the furnace is to___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Sacrificial anode method is used in the protection of pipelines which are buried underground. Sacrificial anode________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  ______________ pipe is the most suitable for carrying sanitary drainage?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The most prominent single cause of corrosion in boiler-tubes, drums, economisers and steam superheaters in a thermal power plant boiler is the_______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Blow off cock is provided in steam boiler to ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The efficiency of a Carnot heat engine operating between absolute temperatures T1 and T2 (when, T1 > T2) is given by (T1 – T2)/T1. The co-efficient of performance (CO.P.) of a Carnot heat pump operating between T1 and T2 is given by_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Venturimeter is used to measure the flow rate of fluids in pipes, when the pipe is in ______________ position ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Gross national product (GNP) means the total value of _______________ in a country ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Work study deals with the _______________ study?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A particle is settling in a liquid under Stokesian conditions. The free falling velocity of the particle is proportional to____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In the acid Bessemer process, the hot metal should have the following composition ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ability of tool steel to resist softening at high temperatures is termed as __________________ hardness?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Electrochemical corrosion can occur, only if ________________ is present in contact with metal?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following processes follows the hardening process for reducing the hardening strains & increasing the toughness of the steel part ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Batch process is preferred over continuous process, when the___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  ‘GASOHOL’ widely used in Brazil as a motor fuel is a mixture of alcohol and____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Specific _________________ is a dimensionless quantity ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Dryness fraction of dry steam is_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following fastening devices has its both ends threaded ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Increase in temperature, in general results in the____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts