Basic Mechanical Engineering Test

Q.  Which of the following statements is/are true?

a. Jaw clutch is a positive clutch
b. The power transmitting capacity of a friction clutch is inversely proportional to the coefficient of friction between contacting surfaces
c. Driving and driven plates in friction clutches are held together due to radial force applied by the helical springs
d. All of the above


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Casting replica used to make the cavity is called as
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  The process of joining similar or dissimilar materials by heating them below 450o C using non-ferrous filler material is called as ______
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  At forging temperature when a compressive force is applied on the material, it deforms
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the average temperature required for hot forging of aluminium alloys?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which process squeezes metals into peaks and troughs with plastic deformation?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which of the following operations is/are performed on a lathe machine?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  The process of chamfering the entrance of a drilled hole is known as_____
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  On drilling machine, which process is known as reaming?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which of the following statements is/are false for machine tools? 1. Pillar drilling machine drills holes up to 75 mm 2. Regulating wheel is a component of surface grinding machine 3. Sensitive drilling machine is also known as bench drilling machine 4. The chuck of an internal grinding machine placed in tailstock is driven by an electric motor
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  The radiation pyrometers work on the principle of ______
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which of the following relations depict relation between Celsius and Fahrenheit scale?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  According to Joule's law, the internal energy of a perfect gas is the function of absolute ______
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  According to Kelvin-Planck statement, it is impossible to construct a device operating on a cycle which transfers heat from ____
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Thermal efficiency of S.I. engines is low, due to ____
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Pump transfers input mechanical energy of an engine, into ______
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which of the following protects penstock due to sudden variation of flow or velocity of water?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  One ton of refrigeration is equal to ______
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the function of a moderator?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which of the following conditions should be satisfied for static balancing? 1. Dynamic forces acting on the system should be zero 2. Couple acting on the system due to dynamic force should be zero 3. Centrifugal forces acting on the system should be zero 4. Couple acting on the system due to centrifugal forces should be zero
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which of the following factors are not responsible for unbalancing in rotating systems?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts