Engineering Mechanics Test Questions

Q.  Which of the following laminas do not have centroid at its geometrical centre?

a. Circle
b. Equilateral triangle
c. Right angled triangle
d. None of the above


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Which of the following conditions do not change the effect of couple?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  If two concurrent forces A and B acting on a point are 200 N and 300 N. What is the magnitude of resultant force, if it makes an angle of 50° with each force?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the angle made by side of a square lamina, if it is freely suspended from a corner with the horizontal?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the C.G of an isosceles triangle of base 20 cm and side 40?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Uniformly distributed load of 5 kN acts on a simply supported beam of length 10 m. What are the reactions at end points of the beam?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the length of a train which crosses a bridge of 150 m in 20 sec with a speed of 40 km/h?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What are the limitations of string law?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Two cars X and Y move on adjacent roads in opposite directions. If velocity of car X and Y is 80 km/hr and 60 km/hr respectively, then what will be the relative velocity of car X w.r.t. Y?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  In 5 seconds a body covers a distance of 50 m and in 10 seconds it covers 80 m with uniform acceleration. What is the distance traveled in 15 seconds?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the maximum distance traveled by a block moving upwards on an inclined plane of 30° with velocity of 20 m/s, if coefficient of friction is 0.23 between the block and inclined plane?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  A constant force of 150 N is applied on a block of 5 kg on a horizontal surface. What is the time required to attain velocity of 40 m/sec by the block?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the angle of projection for a bullet fired over a horizontal plane, when horizontal range is equal to 4 times the maximum height?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the kinetic energy at the highest point, if at an angle of 30° with the horizontal a ball is projected with a kinetic energy E?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which of the following factors are related by work energy principle?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the S.I unit of work done?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which of the following force(s) is a type of conservative force?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the coefficient of restitution (e) for elastic impact?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  If coefficient of restitution is zero during plastic impact, then ___________
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Coefficient of restitution is the ratio of impulse during __________
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Cantilever beam has one end _________ and other end _______.
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts