Process Control & Instrumentation Mcqs for Chemical

Q.  Which of the following is not a variable area flow meter ?

a. Piston type meter
b. Rotameter
c. Magnetic flow meter
d. Orifice and tapered plug meter


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  E.m.f. generated by thermocouples is of the order of ________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The frequency response of a dynamic element shows a constant magnitude ratio at all frequencies. The element exhibits a negative phase shift at all frequencies. The absolute value of the phase shift increases linearly with frequency. The element has the transfer function ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Paramagnetism method is not used for the composition determination of ______________ in gases?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Suppose that the gain, time constant and dead time of a process with the following transfer function: Gc(s) = 10 exp( – 0.1s)/(0.5s + 1) are known with a possible error of ± 20% of their values. The largest permissible gain Kc of a proportional controller needs to be calculated below taking the values of process gain, time constant and dead time as________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Transfer function of transportation lag is___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  An amplitude ratio of 0.1 corresponds to _____________ decibels?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Emf developed by a thermocouple while measuring a temperature of 400°C is 22 mV. The type of thermocouple used is ___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  What is the dynamic error in a critically damped second order instrument for a ramp input (At) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the systems having the following transfer function is stable ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following fluid flow measuring devices can measure the largest flow rate ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The operation of a Rotameter is based on ________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The unit step response of the transfer function 1/(s2 + 2s + 3) _______________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Bode stability method uses ____________ loop transfer function?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For an input forcing function, X(t) = 2t2, the Laplace transform of this function is________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The deflection of the free end of the bimetallic strips in a bimetallic thermometer with temperature is nearly__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Thermal conductivity cell is the primary element of a/an _____________ analyser?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The temperature of tempering oil baths maintained at 400°C during heat treatment of steel is measured by a/an _____________ thermocouple?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following is not a mechanical pressure sensing element ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Working principle of bimetallic thermometers is difference in linear co-efficient of thermal expansion of two strips of different metals welded together. Which of the following has the maximum thermal co-efficient of linear expansion ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Emf developed by a thermocouple, while measuring a temperature of 600°C is about 5.5 mV. The type of thermocouple used is_______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts