Chemical Engineering Basics Mcqs

Q.  Which of the following has the highest modulus of elasticity (about 7 × 106 kg/cm2) ?

a. High speed steel
b. Stainless steel
c. Tungsten carbide
d. Superalloys


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  Ganister contains maximum percentage of_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Triple point of water is__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Reynolds number of a fluid flowing in a circular pipe is 10,000. What will be the Reynolds number when the fluid velocity is decreased by 30% & the pipe diameter is increased by 30% ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Holes for riveting purposes should be preferably made by________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Electrolytic reduction cell used for conversion of calcined Al2O3 to Al is a carbon lined furnace operating at 800-900 °C. The purpose of electric current supplied to the furnace is to___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Sacrificial anode method is used in the protection of pipelines which are buried underground. Sacrificial anode________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  ______________ pipe is the most suitable for carrying sanitary drainage?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The most prominent single cause of corrosion in boiler-tubes, drums, economisers and steam superheaters in a thermal power plant boiler is the_______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Blow off cock is provided in steam boiler to ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The efficiency of a Carnot heat engine operating between absolute temperatures T1 and T2 (when, T1 > T2) is given by (T1 – T2)/T1. The co-efficient of performance (CO.P.) of a Carnot heat pump operating between T1 and T2 is given by_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Venturimeter is used to measure the flow rate of fluids in pipes, when the pipe is in ______________ position ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Gross national product (GNP) means the total value of _______________ in a country ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Work study deals with the _______________ study?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A particle is settling in a liquid under Stokesian conditions. The free falling velocity of the particle is proportional to____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In the acid Bessemer process, the hot metal should have the following composition ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ability of tool steel to resist softening at high temperatures is termed as __________________ hardness?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Electrochemical corrosion can occur, only if ________________ is present in contact with metal?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following processes follows the hardening process for reducing the hardening strains & increasing the toughness of the steel part ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Batch process is preferred over continuous process, when the___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  ‘GASOHOL’ widely used in Brazil as a motor fuel is a mixture of alcohol and____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts