Thermodynamics Test Questions


Q.  Which of the following can be regarded as gas so that gas laws could be applicable, within the commonly encountered temperature limits ?

a. 02, N2, steam, C02
b. Oz, N2, water vapour
c. S02, NH3, C02, moisture
d. 02, N2, H2, air
e. steam vapours, H2, C02


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Volume of blast furnace slag is about _______________ times the volume of hot metal (pig iron) of the same weight ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Colour comparator is used to measure the___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  A reduction in thermal resistance during heat transfer does not occur in the___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Plastics as a material of construction suffer from the drawback of low_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The thickness of oxide film is y at time t. If K1, K2 and K3 are the temperature dependent constants, the parabolic law of oxidation is given by __________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Biological shield in a nuclear reactor is generally provided to protect against the__________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The most detrimental impurity in high pressure boiler feed water is ___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Sub zero treatment of steel is done to____________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  In Newton’s law of viscosity, which states that the shear stress is proportional to the _____________ Co-efficient of viscosity is called dynamic or absolute viscosity(where, V = velocity, Vg = velocity gradient) ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Which of the following is not categorised as the ore agglomeration process ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Tumbling is the process of improving the ________________ of the materials/parts ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Young’s modulus of a material is the measure of its ___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Which of the following materials has the least scrap value ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Which of the following is used to produce draught in the locomotive boilers ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Alcohols are not suitable as diesel engine fuel because the cetane number of alcohols is____________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The process of removal of scale formed during hot rolling of steel is termed as_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Boiling point of water gets lowered at high altitudes (e.g., hills), because ___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The leaching solvent used in Baeyer’s process for the purification of bauxite is___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  With increase in annealing temperature, the following defect density decreases?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  A gas which is collected over water becomes moistened due to water vapor, exerts its own partial pressure at the gas temperature, which is termed as its_______________?
Category: Chemical Engineering Mcqs,   Published by: teswesm