Elex Product Design Test Questions


Q.  Which defects affect the quality of products by showing the deviations of values from the standard values as per the product specifications?

a. Major defects
b. Minor defects
c. Critical defects
d. None of the above


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  What does the word “End do” in a pseudo code imply?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which terminology of PCB represents a thin photo-sensitive polymer by supporting photographic pattern of single traces or IC pads for etching?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  The actual cost of PCB can be evaluated on the basis of ________
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which factors contribute to the occurrence of mechanical stress?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which type of PCB requires minimum soldering on component side in order to avoid replacement oriented difficulties?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  What effects can be observed if the separate power and ground planes are provided with large conducting surfaces for better decoupling in PCB layouts?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which problems are about to occur if PCB is not designed properly in a confined manner for digital circuits? A. Diffraction B. Refraction C. Ground & Supply-line Noise D. Electromagnetic Interference
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which among the following is a terrestrial navigation system that utilizes low frequency radio transmitters and the time interval received from several radio signals in order to determine the position of ship or an aircraft?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Fractional bandwidth basically refers to the bandwidth of device, which gets divided by __________
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Free Space Path Loss (FSPL) is proportional to the square of _________
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which among the below mentioned assertions is not a reason responsible for the occurrence of fading?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  What is the range of SINAD numbers associated with the threshold for reasonable intelligibility of voice especially in SINAD measurement system?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which among the design characteristics of MUX specifies that the two channels can never be connected instantaneously?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  The requisite amount of time for output in order to track an input within the specific error band after delivering the sample command while designing sample and hold circuitry is known as ___________
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which type of voltage regulator exhibits an excessive power dissipation in a series pass transistor?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  The method used for screening of products along with the design evaluation in order to catch early-term latent defects is renowned as Environmental Stress Screening (ESS) or __________
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Bump is basically the force experienced by a product since it is bounded on a _______
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which type of test chamber style in an environmental testing has a provision of access through door so as to reach and handle the contents of chamber?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which actions must be undertaken over the souring consequences of finishes in the vibration type of enclosure testing?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  In mechanical shock type of an enclosure testing, the usability of materials with high tensile strength is necessary for overcoming the effect of __________
Category: Electronic Engineering Questions,   Published by: teswesm