# Mechanical System Design Test Questions

Q.  Which belt conveyor prevents sliding down of material at an inclination of 55° with horizontal?

a. Flat belt conveyor
b. Troughed belt conveyor
c. Blanket belt conveyor
d. Woven wire belt conveyors

ANSWER: See Answer

No explanation is available for this question!
 MCQs:  In projectile motion, which of the following factors affecting the actual path of motion are neglected? Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  Which of the following is represented by the area under force-displacement diagram? Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  According to work energy principle, a particle of mass m when subjected to unbalanced force system, the work done during displacement by all forces is equal to change in ____________ during displacement. Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  The force for which work done is independent of _______ is called as conservative force. Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  A ball is dropped on a horizontal surface from a height of 15 m. What will be the rebounding height of the ball after striking the surface? (coefficient of restitution = 0.8) Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  Which of the following laws derive impulse moment principle? Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  If a body in equilibrium condition is acted by three forces at three points, then the line of action of these forces should be _____ Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  According to Lami's theorem, a body is in equilibrium condition if each force among three ____________ are proportional to sine angle between other two. Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  If n > 2j – R, then the truss is called as _________. (n = number of joints, j = number of members, R = number of reaction components) Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  Which of the following statements is false about frame/truss? Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  Which motion has magnitude of static frictional force directly proportional to normal reaction? Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  Frictional force depends on ________ Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  Which of the following conditions do not change the effect of couple? Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  If two concurrent forces A and B acting on a point are 200 N and 300 N. What is the magnitude of resultant force, if it makes an angle of 50° with each force? Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  What is the angle made by side of a square lamina, if it is freely suspended from a corner with the horizontal? Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  What is the C.G of an isosceles triangle of base 20 cm and side 40? Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  Uniformly distributed load of 5 kN acts on a simply supported beam of length 10 m. What are the reactions at end points of the beam? Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  What is the length of a train which crosses a bridge of 150 m in 20 sec with a speed of 40 km/h? Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  What are the limitations of string law? Category: Mechanical Engineering Questions,   Published by: T-Code Scripts MCQs:  Two cars X and Y move on adjacent roads in opposite directions. If velocity of car X and Y is 80 km/hr and 60 km/hr respectively, then what will be the relative velocity of car X w.r.t. Y? Category: Mechanical Engineering Questions,   Published by: T-Code Scripts