Design of Machine Elements


Q.  What is the effect of large diametral quotient on worm and worm wheel?

a. Strength and rigidity of worm shaft is high
b. Efficiency of worm shaft increases
c. Worm shaft becomes weaker
d. All of the above


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Load acting on bearing in its plane of rotation is called as __________
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Which of the following elements is not used as a roller in roller bearings?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Which of the following bearings carry thrust load in one direction?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A cylindrical roller bearing is subjected to radial force of 4500 N and application factor 1.3. What is the equivalent dynamic load acting on bearing if it has 90% reliability with desired life of 10000 hrs?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A worm gear pair has 2 starts on worm thread, 11.2 as diametral quotient, 2 as module and 38 number of teeth on worm gear. How is the gear pair designated with these specifications?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  What is the shortest distance between worm gear and axes of the worm for a worm gear pair designated as 2/40/10/8?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  If pressure angle is 22° and coefficient of friction is 0.05. What is the axial force acting on the worm gear designated as 1/40/10/5, if tangential force of 1200 N acts on it?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Which of the following statements is/are true for V-belts?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A V-belt pulley transmits power to flat belt pulley. If the coefficient of friction is 0.25 then which pulley governs the design? (β = 21° & α = 0.2)
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A V-belt pulley has belt velocity 20 m/s and mass 0.7 kg per meter. If allowable tension in the belt is 600 N then what will be the power transmitting capacity of belt? (Assume μ = 0.5 & θ = 2.5 rad)
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Lang lay ropes offer more resistance to __________
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  What does number 6 indicate in the class of wire rope 6 x 37 (18/12/6/1)?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Which of the following formula is used to calculate oil-film thickness in hydrodynamic bearings?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  In half wave rectifiers, diode conducts during
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  Specific resistance of a material is
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  Which among the following is true about ohm’s law?
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  In any network of wires carrying currents, the algebraic sum of all currents meeting at a point is equal to
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  Electrical appliances which works on the electromagnetic principle is / are
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  The materials with permeability less than unity are called
Category: Electrical Engineering Questions,   Published by: teswesm
MCQs:  The magnetic materials which are strongly attracted by the magnet is
Category: Electrical Engineering Questions,   Published by: teswesm