Electronic Devices & Circuits Test Questions


Q.  What is/ are the necessity /ies of using a vertical structure in Power BJTs?

a. Increase in cross-sectional area to allow the flow of device current
b. Reduction in on-state power dissipation of transistor
c. Reduction in thermal resistance to keep the problem of power dissipation under control
d. All of the above


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Which type of breakdown effect gets enhanced due to parasitic BJT action along with increase in drain current solely by the reduction in size of MOSFET?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which among the below stated transistors operate in an active region for the purpose of amplification?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Under which category/region of the below specified regions does EMOSFET operate for switching-based applications?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which among the below mentioned implementation strategies is/are precise to obtain an AC equivalent circuit of MOSFET? A. Replacement of all capacitors by open circuits B. Replacement of all capacitors by short circuits C. Setting of all DC voltages to zero D. Setting of all DC voltages to unity
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which type of temperature dependent resistor exhibits a positive temperature coefficient of resistivity?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which process plays a crucial role in devising the independency of operating point over the variations in temperature or transistor parameters?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which techniques is/are adopted for reducing the drift in the operating point especially when the loss of signal is intolerable?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  On which factor/s do/does the value of thermal resistance depend?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Consider the assertions given below. A. Replacement of each coupling and bypass capacitors by a short circuit B. Replacement of transistor by its hybrid equivalent model for further analysis C. Replacement of DC voltage sources by a short circuit Which is the correct sequential order of steps to be carried out for analysis of a transistor amplifier circuit?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Why is the Darlington configuration not suitable for more than two transistors?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which among the below mentioned circuits resemble its behaviour similar to that of an amplifier in high frequency region, as the response decreases with an increase in frequency?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which among the following is not an advantage of RC coupled amplifiers?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  What should be the value of unity gain frequency for a short circuit CE transistor with gain of 30 at 4MHz and cut-off frequency of about 100 kHz?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Stability of a transfer gain is generally defined as the reciprocal of _______
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  What are the consequences over the non-linear distortion by the inception of negative feedback?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  According to the property of tuned circuit used in LC oscillators, the decay rate is proportional to________
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which among the following measures is/are adopted/used for improving the frequency stability in Colpitt's oscillator?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which among the following oscillators are specifically preferred at high frequencies?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which among the below stated parameters gets affected due to drift region in the power transistor?
Category: Electronic Engineering Questions,   Published by: teswesm
MCQs:  Which types of power transistors have the capability to withstand the higher junction temperatures?
Category: Electronic Engineering Questions,   Published by: teswesm