RCC Structures Design Mcqs


Q.  Top bars are extended to the projecting parts of the combined footing of two columns Ldistance apart for a distance of_______________?

a. 0.1 L from the outer edge of column
b. 0.1 L from the centre edge of column
c. Half the distance of projection
d. One -fourth the distance of projection


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  If R and T are rise and tread of a stair spanning horizontally, the steps are supported by a wall on one side and by a stringer beam on the other side, the steps are designed as beams of width_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If p1 and P2 are effective lateral loadings at the bottom and top exerted by a level earth subjected to a super-load on the vertical face of height h of a retaining wall, the horizontal pressure p per unit length of the wall, is____________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The transverse reinforcements provided at right angles to the main reinforcement_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Long and short spans of a two way slab are l and l and load on the slab acting on strips parallel to lx and ly be wx and wy respectively. Accordingy to xRankine Grashoff theory___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  In the zone of R.C.C. beam where shear stress is less than 5 kg/cm2, nominal reinforcement is provided at a pitch of________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  High strength concrete is used in pre-stressed member________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  on a circular slab of radius , the maximum radial moment at the centre of the If is the load slab, is WR²/16_____________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the permissible compressive and tensile stresses in a singly reinforced beam are 50 kg/cm2 and 1400 kg/cm2 respectively and the modular ratio is 18, the percentage area At of the steel required for an economic section, is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The modular ratio m of a concrete whose permissible compressive stress is C, may be obtained from the equation.
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Enlarged head of a supporting column of a flat slab is technically known as______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If A is the area of the foundation of a retaining wall carrying a load W and retaining earth of weight w per unit volume, the minimum depth (h) of the foundation from the free surface of the earth, is )/(1 + sin )]_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Thickened part of a flat slab over its supporting column, is technically known as_____________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The pitch of the main bars in a simply supported slab, should not exceed its effective depth by_____________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If is the sectional area of a pre-stressed rectangular beam provided with a tendon pre -stressed by a force through its centroidal longitudinal axis, the compressive stress in concrete, is_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Side face reinforcement shall be provided in the beam when depth of the web in a beam exceeds_____________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The minimum head room over a stair must be_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If q is the punching shear resistance per unit area a, is the side of a square footing for a column of side b, carrying a weight W including the weight of the footing, the depth D. of the footing from punching shear consideration, is____________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the length of a combined footing for two columns l metres apart is L and the projection on the left side of the exterior column is x, then the projection y on the right side of the exterior column, in order to have a uniformly distributed load, is (where is the distance of centre of gravity of column loads______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the tendon is placed at an rectangular beam (sectional top edge)________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The Young’s modulus of elasticity of steel, is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm