Structural Analysis Mcqs

Q.  To generate the j the column of the flexibility matrix________________?

a. a unit force is applied at coordinate j and the displacements are calculated at all coordinates
b. a unit displacement is applied at co-ordinate j and the forces are calculated at all coordinates
c. a unit force is applied at coordinate j and the forces are calculated at all coordinates
d. a unit displacement is applied at co-ordinate j and the displacements are calculated at all co-ordinates


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  The forces acting normally on the cross section of a bar shown in the given figure introduce_____________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The load on a spring per unit deflection, is called______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A close coil helical spring of mean diameter D consists of n coils of diameter d. If it carries an axial load W, the energy stored in the spring, is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The moment of inertia of a triangular section (height h, base b) about its base, is_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The assumption in the theory of bending of beams is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A concentrated load P is supported by the free end of a quadrantal ring AB whose end B is fixed. The ratio of the vertical to horizontal deflections of the end A, is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that stress in the wire does not exceed 100 N/mm2 is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The maximum deflection due to a uniformly distributed load w/unit length over entire span of a cantilever of length l and of flexural rigidly EI, is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The forces acting normally on the cross section of a bar shown in the given figure introduce_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A spring of mean radius 40 mm contains 8 action coils of steel (N = 80000 N/mm2), 4 mm in diameter. The clearance between the coils being 1 mm when unloaded, the minimum compressive load to remove the clearance, is_____________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The strain energy stored in a spring when subjected to greatest load without being permanently distorted, is called______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The strain energy due to volumetric strain________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated load W at its mid-span. The same bar experiences an extension e under same tensile load. The ratio of the maximum deflection to the elongation, is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In the truss shown in given figure the force in member DC is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of lateral strain to axial strain of a homogeneous material, is known___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The force in BF of the truss shown in given figure, is_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of maximum shear stress to average shear stress of a circular beam, is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For a strongest rectangular beam cut from a circular log, the ratio of the width and depth, is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  m1 and m2 are the members of two individual simple trusses of a compound truss. The compound truss will be rigid and determinate if__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The greatest load which a spring can carry without getting permanently distorted, is called_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts