Process Equipment & Plant Design Mcqs for Chemical

Q.  To avoid the tearing off the plate of an edge, the margin (i.e., the minimum distance from the centre of the rivet hole to the nearest edge of the plate) should be equal to ____________________?

a. 0.5 d
b. d
c. 1.5 d
d. 2.5 d


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  In a multiple effect evaporator system having ‘n’ effects, the amount of water evaporated per unit surface area in approximately equal to _____________ times that in a single effect?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Slope of counter-current flow rotary drier is in the range of ____________ meter/metre?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Liquid gradient over a tray can be minimised by________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Ratio of tube length to shell diameter for a shell and tube heat exchanger is________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  (Le/D) for couplings and unions would be_______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A shell may by termed as thin if its thickness to diameter ratio is less than 0.1. The factor which can be neglected in the calculation of membrane stresses is________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The average velocity in the tubes of a 1-4 heat exchanger is ______________ times that in 1-1 heat exchanger having the same size & number of tubes and operated at same liquid flow rate ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  _____________ heat exchanger is also known as ‘hair pin type’ exchanger?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a shell and tube heat exchanger, triangular pitch arrangement as compared to square pitch arrangement ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Minimum tube pitch recommended for shell and tube heat exchangers is about _______________ times the outside diameter of the tube?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following efficiencies can be greater than 100% ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Angled baffles are preferred in the agitation tank to control the swirling action; if the viscosity of the liquid to be mixed is about 200 poise. However, the baffle may be completely eliminated for mixing liquids having viscosity above ____________________ poise?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  What is the slope of the operating line in the rectifying section of a distillation column ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of lateral strain to linear strain is termed as the___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Normal screwed fittings are used for pipes upto a diameter of _______________ inches?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio, (propeller agitator dia/tank dia) is normally taken as____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Tube height in a calandria type evaporator is normally less than _______________ metres?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Weep holes provided in the plates of a distillation column ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick out the wrong statement about distillation operation__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick out the wrong statement pertaining to ‘Horton sphere’ used for the storage of liquid ammonia ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts