Process Control & Instrumentation Mcqs for Chemical

Q.  Thermal conductivity based continuous flue gas analyser makes use of varying thermal conductivity of the constituents of flue gases. Which of the following constituents of flue gases has the maximum thermal conductivity ?

a. CO2
b. N2
c. O2
d. CO


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  Positioning controllers are used for _______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Operating range of a temperature measuring instrument is 800 to 1600°C. It could be a/an _____________ pyrometer?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A bimetallic thermometer as compared to industrial mercury in glass thermometer has almost the same_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The maximum service temperature for fibre glass used as thermocouple wire insulation material is __________ °C?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Time constant is the __________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Continuous shell temperature measurement in a liquid-liquid heat exchanger is done by a __________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  What is the ratio of output amplitude to input amplitude for a sinusoidal forcing function in a first order system ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Flow rate through an orifice is _____________ the pressure differential?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following is not the triple point of water ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Measurement of sub-zero Celsius temperature in industry is done most commonly by __________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Characteristic equation is the denominator of ____________ loop transfer function?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Smoke density of the flue gas going out of the chimney is measured by a __________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The experimental response of the controlled variable y(t) for a step change of magnitude ‘P’ in the manipulated variable x(t) is shown below: The appropriate transfer function of the process is_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Mercury manometer (U-tube type) exemplifies a ______________ order system?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Liquid argon level in a pressurised storage tank (at 3 kg/cm2) is measured by a/an ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  E.m.f. generated by thermocouples is of the order of ________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The frequency response of a dynamic element shows a constant magnitude ratio at all frequencies. The element exhibits a negative phase shift at all frequencies. The absolute value of the phase shift increases linearly with frequency. The element has the transfer function ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Paramagnetism method is not used for the composition determination of ______________ in gases?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Suppose that the gain, time constant and dead time of a process with the following transfer function: Gc(s) = 10 exp( – 0.1s)/(0.5s + 1) are known with a possible error of ± 20% of their values. The largest permissible gain Kc of a proportional controller needs to be calculated below taking the values of process gain, time constant and dead time as________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Transfer function of transportation lag is___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts