Strength of Materials Test Questions

Q.  The weakest section of a diamond riveting is the section which passes through ___________________?

a. the first row
b. the second row
c. the central row
d. one rivet hole of the end row
e. none of the above


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  The C.G. of a solid hemisphere lies on the central radius 3r_________________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  A flywheel on a motor goes from rest to 1000 rpm in 6 sec. The number of revolutions made is nearly equal to_________________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  If n = number of members andy = number of joints, then for a perfect frame, n =________________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  The necessary condition for forces to be in equilibrium is that these should be_____________________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  The maximum frictional force which comes into play when a body just begins to slide over another surface is called________________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  A single force and a couple acting in the same plane upon a rigid body_________________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  A particle inside a hollow sphere of radius r, having coefficient of friction -rr can rest upto height of___________________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  The effort required to lift a load W on a screw jack with helix angle a and angle of friction
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Coulomb friction is the friction between_____________________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  A projectile is fired at an angle 9 to the vertical. Its horizontal range will be maximum when 9 is__________________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Shear stress induced in a shaft subjected to tension will be__________________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  A key is subjected to side pressure as well at shearing forces. These pressures are called_________________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  The torsional rigidity of a shaft is expressed by the_______________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Longitudinal stress in a thin cylinder is__________________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  A boiler shell 200 cm diameter and plate thickness 1.5 cm is subjected to internal pressure of 1.5 MN/m , then the hoop stress will be_________________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  The deformation of a bar under its own weight compared to the deformation of same body subjected to a direct load equal to weight of the body is_______________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Rivets are made of following type of material_________________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  If the rivets in adjacent rows are staggered and the outermost row has only one rivet, the arrangement of the rivets is called__________________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  A riveted joint in which every rivet of a row is opposite to other rivet of the outer row, is known as______________________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Efficiency of a riveted joint is the ratio of its strength (max. load it can resist without failure) to the strength of the unpunched plate in_________________?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts