Railway Engineering Mcqs

Q.  The type of bearing plate used in all joints and on curves to give better bearing area to the rails is___________________?

a. flat mild steel bearing plate
b. mild steel canted bearing plate
c. cast iron anti creep bearing plate
d. none of the above


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Switch angle depends on______________? i) heel divergence ii) length of tongue rail iii) flangeway clearance iv) throw of switch The correct answer is?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a scissors cross-over, the crossings provided are_________________? i) 2 obtuse angle crossings ii) 4 obtuse angle crossings iii) 4 acute angle crossings iv) 6 acute angle crossings The correct answer is ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The reception signal is__________________? i) outer signal ii) home signal iii) starter iv) advanced starter The correct answer is?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  To ensure exact gauge, the gauge tie plates are provided at_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a B.G. railway track, the specified ruling gradent is 1 in 250. The horizontal curve of 3° on a gradient of 1 in 250 will have the permissible gradient of__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If ‘A’ is the angle formed by two gauge faces, the crossing number will be____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the thickness of thinnest outside plate is 10 mm, then the maximum pitch of rivets in tension will be taken as______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  When the axis of load lies in the plane of rivet group, then the rivets are subjected to________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Bending compressive and tensile stresses respectively are calculated based on_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  When the axis of load lies in the plane of rivet group, then the most heavily loaded rivet will be the one which________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The difference between gross diameter and nominal diameter for the rivets up to 25 mm diameter is__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the thickness of plate to be connected by a rivet is 16 mm, then suitable size of rivet as per Unwin’s formula will be__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The heaviest I-section for same depth is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following types of riveted joint is free from bending stresses ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a gusseted base, when the end of the column is machined for complete bearing on the base plate, then the axial load is assumed to be transferred to base plate__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  By providing sufficient edge distance, which of the following failures of riveted joint can be avoided ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As compared to field rivets, the shop rivets are________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Efficiency of a riveted joint, having the minimum pitch as per IS : 800, is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Bolts are most suitable to carry_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  When the bolts are subjected to reversal of stresses, the most suitable type of bolt is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts