|
MCQs: The LMTD correction factor (FT) is defined as the __________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Which of the following is the best tube material from thermal conductivity point of view alone ?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Power required for agitation depends upon the______________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Stage efficiency for packed tower varies with the____________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Tube wall thickness depends on the corrosiveness of the fluids and their operating pressure & temperature and is specified by Birmingham wire gauge (B.W.G)-a number which varies from 8 to 18 with the numbers 14 and 16 being more commonly used. Outside diameter of tubes varies from about 15 to 50 mm; however a tube of less than _____________ mm outside diameter is generally not recommended for fouling fluids ?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: In hydrostatic testing of welded pipe (for leakage, strength etc.) the ratio of minimum hydrostatic test pressure to internal design pressure is around __________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: In a shell and tube heat exchanger, the shortest centre to centre distance between the adjacent tubes is__________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: If ‘D’ is the inside diameter of the shell of a shell and tube heat exchanger, then the baffle spacing is usually in the range of__________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: For turbulent flow (NRe > 2100) of low viscosity fluid (μ > 20cp) in steel pipes, the optimum inside pipe diameter is given by(where, Q = fluid flow rate, ft3/sec, ρ = fluid density, lb/ft3 μ = fluid viscosity, centipoise Di = optimum inside pipe diameter, inches) ?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Scale up problem in design based on the similarity concept takes into account _______________ similarity?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: The longitudinal stress induced in a thin walled cylindrical vessel under internal pressure is_________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: 1.2 to 3.8 cms is the value of the ______________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: In a pressure vessel containing multiple openings of various dimensions at different parts, stress concentration at the edges of the opening is maximum which becomes negligibly small beyond the area covered by ______________ times the hole diameter?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Removable connection of tubes to tube sheet is called___________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Bubble cap tray is the most commonly used tray in large distillation column, because______________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: (Le/D) for a Tee (used as elbow, entering run) would be around _______________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: At equal mass velocities, the values of film co-efficients for gases as compared to that for liquids are generally ?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: The design stress, which is more than the damaging stress, is the least unit stress that will render a member unfit for service before the end of its normal life. The design stress factor or factor of safety indicates the margin between design stress and the _______________ stress?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Baffles are provided in a shell and tube heat exchanger to increase the turbulence and velocity of the shell side fluid. Which of the following shaped baffles does not fall in the category of transverse baffle ?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Value of Peclet number = ∞, is the representative of___________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
