|
MCQs: If is the rugosity coefficient, is the bed slope of sewer, the velocity of flow in m/sec may be obtained by the formula V = (1/n) r2/3 s1/2 evolved by_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The sewage treatment in septic tanks is due to__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: In a sludge digestion tank if the moisture content of sludge V1 litres is reduced from p1 % to p2 % the volume V2 is____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: You are asked to design sewer pipes of diameters 0.4 m to 0.9 m at maximum flow, you will assume the sewer flow running at___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: For a peak discharge of 0.0157 cumec, with a velocity of 0.9 m/sec, the diameter of the sewer main, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The most effective arrangement for diverting excess storm water into a natural drainage, is____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: For estimating the peak run off the rational formula Q = 0.0278 KpA was evolved by______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The settlement velocity of a solid (diameter 0.5 mm, specific gravity 1.75) in water having temperature 10°C, is______________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The laying of sewers is done with____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: For detecting the nitrites in the sewage, the matching colour may be developed by adding_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Fresh sewage is generally_____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: It is customary to design a sewer for D.W.F. on the basis of________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The following is the physical characteristic of sewage___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: For laying a sewer line in a trench of 2 m width, an offset line is marked on the ground parallel to the given centre line at a distance of___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The most dangerous pollutant in vehicular emissions is____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The sewer which collects the discharge from a collecting system and delivers it to a treatment plant, is known_____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A sewer pipe contains 1 mm sand particles of specific gravity 2.65 and 5 mm organic particles of specific gravity 1.2, the minimum velocity required for removing the sewerage, is_____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The settlement of a particle in sedimentation tank, is affected by_____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If the over land flow from the critical point to the drain is 8 km and the difference in level is 12.4 m, the inlet time is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The minimum recommended diameter of sewers, is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
