MCQs: The rail is designated by its__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: Two important constituents in the com-position of steel used for rail are_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: The following tests are conducted for rails _________________?
i) falling weight test
ii) tensile test
iii) hammer test
The compulsory tests are?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: Which of the following factors govern the choice of the gauge ?
i) volume and nature of traffic
ii) speed of train
iii) physical features of the country
The correct answer is ?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: The formation width for a railway track depends on the_________________?
i) type of gauge
ii) number of tracks to be laid side by side
iii) slope of sides of embankment or cutting
The correct answer is?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: Study the following statements regarding creep_________________?
i) Creep is greater on curves than on tangent railway track
ii) Creep in new rails is more than that in old rails
iii) Creep is more on steep gradients than on level track
The correct answer is?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: Switch angle depends on______________?
i) heel divergence
ii) length of tongue rail
iii) flangeway clearance
iv) throw of switch
The correct answer is?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: In a scissors cross-over, the crossings provided are_________________?
i) 2 obtuse angle crossings
ii) 4 obtuse angle crossings
iii) 4 acute angle crossings
iv) 6 acute angle crossings
The correct answer is ?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: The reception signal is__________________?
i) outer signal
ii) home signal
iii) starter
iv) advanced starter
The correct answer is?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: To ensure exact gauge, the gauge tie plates are provided at_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: In a B.G. railway track, the specified ruling gradent is 1 in 250. The horizontal curve of 3° on a gradient of 1 in 250 will have the permissible gradient of__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: If ‘A’ is the angle formed by two gauge faces, the crossing number will be____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: If the thickness of thinnest outside plate is 10 mm, then the maximum pitch of rivets in tension will be taken as______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: When the axis of load lies in the plane of rivet group, then the rivets are subjected to________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: Bending compressive and tensile stresses respectively are calculated based on_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: When the axis of load lies in the plane of rivet group, then the most heavily loaded rivet will be the one which________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: The difference between gross diameter and nominal diameter for the rivets up to 25 mm diameter is__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: If the thickness of plate to be connected by a rivet is 16 mm, then suitable size of rivet as per Unwin’s formula will be__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: The heaviest I-section for same depth is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: Which of the following types of riveted joint is free from bending stresses ?
Category: Civil Engineering Mcqs, Published by: teswesm
|