|
MCQs: Column support for the roof of cylindrical storage tank must be provided for___________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: The stress developed in a material without any permanent set is called the____________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Which of the following material is seldom used for pressure vessel construction ?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: For laminar flow (NRe < 2100) in steel pipe, the optimum inside pipe diameter is given by____________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Correct use of ‘factor of safety’ is very important in equipment design. It is defined as the ratio of the___________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: In a multipass shell and tube heat exchanger, the shell side cross flow area does not depend upon______________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Tube side pressure drop in a 1-2 heat exchanger (for turbulent flow of fluids through the tubes) is about __________ times, that in a 1-1 heat exchanger having the same size & number of tubes and operated at the same liquid flow rate ?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Holes of a sieve tray are arranged in triangular pitch of _________________ times the hole diameter?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Fresh water carrying pipelines in chemical industries are coloured with _______________ color?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Pressure drop (Δp) and the superficial gas mass velocity (G) in case of packed absorption tower operating in the preloading range are related as_________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: The operating velocity in the absorption tower is usually 40-50% of the flooding velocity. Packed absorption towers are normally designed for a pressure drop of about _________________ mm of water column per metre height of packing?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: It is not desirable to design a heat exchanger for LMTD correction factor, FT, of less than _________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Overall distillation column efficiency for most of the refinery columns can be given by (for μ = 0.07 – 1.4 cp and relative volatility < 4) (where ε = overall column efficiency, % μ = molal average viscosity of feed at average column temperature and pressure, cp Δp = pressure drop per tray, psi) ?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: In a ______________ riveted joint, the rivets in the various rows are opposite to each other?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: In actual operation of a bubble cap distillation tower, the ______________ at the bottom of the tower is more than that at the top of the tower?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Smoker’s equation for the calculation of number of equilibrium stages in a continuous binary distillation column is used, when the_________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: (Le/D) for fully open gate valves would be __________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: _______________ shaped roof is most commonly used for cylindrical tanks ?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: The minimum plate spacing in most of the petroleum refinery distillation columns (of dia > 3 ft) is normally _____________ inches?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: ____________________ strain is measured using a ‘strain rosetter’ ?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
