Strength of Materials Test Questions

Q.  The relation between modulus of elasticity (E), modulus of rigidity (G) and bulk modulus (K) is given as ________

a. K+G / (3K+ G)
b. 3 KG / (3K+ G)
c. 3 KG / (9K+ G)
d. 9 KG / (3K+ G)


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  If the effective length of a column is twice the actual length, then the column is ________
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the value of Rankine's constant for cast iron?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the value of shear stress acting on a plane of circular bar which is subjected to axial tensile load of 100 kN? (Diameter of bar = 40 mm , θ = 42.3°)
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  The angle between normal stress and tangential stress is known as angle of ______
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Minor principal stress has minimum ________
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  According to maximum strain energy theory, failure of material due to complex stresses occurs when total stored energy per unit volume at a point ___________
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Principal stress of 30 Mpa and -70 Mpa acts on a material which has elastic limit stress in simple tension and compression as 60 Mpa and 200 Mpa respectively. Specify the reason for failure of the material assuming maximum principle stress theory.
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  A circular bar is subjected to an axial force and shear force, the difference between two principle stresses is 120 Mpa. Based on maximum shear stress theory what is the factor of safety, if elastic limit of the bar is 300 Mpa?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  For designing ductile materials, which of the following theories is/are used?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Shear stress energy theory is called as ______
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which gear is used if the axes of two shafts are neither intersecting nor parallel?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Spiral gears are used only if the axes of two shafts are non-intersecting, non-parallel and __________.
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  In which of the following processes, tooth ends are made thinner?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What are the advantages of smaller pressure angles?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  In force analysis of spur gears which component of force assists the rotation on driven gear?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  A helical gear has normal module of 6 mm. What is the transverse module if helix angle is 25°?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the axial pitch for helical gears if helix angle is 25° and normal module is 7?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  Which of the following formulae of velocity factor (K) is considered if helical gears of medium accuracy are manufactured by hobbing process followed by shaving?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  What is the pitch cone distance of bevel gear, if pitch circle diameter of bevel pinion and gear is 20 and 30 respectively?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts
MCQs:  A pair of straight bevel gears consists of 16 pinion teeth and 42 gear teeth. What are the pitch cone angles of pinion and gear? 67.60° & 32.4°?
Category: Mechanical Engineering Questions,   Published by: T-Code Scripts