Process Equipment & Plant Design Mcqs for Chemical

Q.  The ratio of volumes of the mixed reactor to the plug flow reactor (for identical feed composition, flow rate, conversion, and for all positive reaction orders) is always ?

a. 1
b. < 1
c. > 1
d. Equal to the order of reaction


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  Thin spherical shells subjected to internal pressure, develop ______________ stresses?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A single pass air heater is connected to a two pass unit. For the air flow rate and other conditions remaining the same, the film heat transfer co-efficient for air will vary in the ratio of_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A cylindrical pressure vessel of volume 6 πm3 has to be designed to withstand a maximum internal pressure of 10 atm. The allowable design stress of the material is 125N/mm2 and corrosion allowance is 2 mm. The thickness of the vessel for a length/diameter ratio of 3 will be close to________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of down take area to cross-sectional area of the tube, for calandria type evaporator ranges from_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The thickness of heat transfer plates used in the plate type heat exchanger ranges from _____________ mm, pressed in a single piece provided with grooves & corrugations?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Circumferential (hoop) stress in a thin cylindrical vessel under internal pressure is _____________ the longitudinal stress?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The optimum size ratio for two mixed reactors in series depends on the kinetics of the reaction and the conversion level. For reaction orders more than one, the_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For turbine agitator, the impeller diameter is about_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Commercial packed scrubbers are normally designed for a pressure drop range of ______________ mm water column per metre of packed height?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The slope of operating line in the rectifying section of a distillation column is unity, if the reflux ratio is___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Overall mass transfer co-efficient in case of absorption of __________ in water is based on the gas film co-efficient only, as the mass transfer process is gas film (phase) controlling ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Minimum baffle spacing recommended in a shell and tube heat exchanger is equal to _____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The most common standard size of bubble caps used in industrial operation is___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Heat transfer co-efficient, hG(Kcal/hr.m2 .°C) and mass velocity of air, G (kg/hr.m2 ) for air flow parallel to the surface in case of constant drying rate in batch drying is related as hG = 0.0176G0.8. But when the flow of air perpendicular to the surface is encountered, this equation changes to ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Height equivalent to a theoretical plate (HETP) is the height of packing that will give the same separation as one theoretical plate in gas-liquid mass transfer operations like distillation, absorption/stripping and humidification/dehumidification. HETP which is experimentally determined, depends upon the_______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Liquid gradient over the tray results due to the___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of tube length to shell diameter in case of liquid shell and tube heat exchanger ranges from__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The slope of the feed line in distillation operation is given by (where, q = fraction of the feed stream that is liquid ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  ____________ head is the most economical for cylindrical vessels designed for operating at high pressure (> 15 atm.)?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The testing pressure of storage tanks and pressure vessels designed as per Indian standard codes should be about ______________ times the design pressure?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts