|
MCQs: The S.F. diagram of a loaded beam shown in the given figure is that of________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: P = /4L² is the equation of Euler’s crippling load, if__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2 MN/mm2, the tensile force developed at a temperature of 50°C, is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: H V are the algebraic sums of the forces resolved horizontally and vertically respectively, M is the algebraic sum of the moments of forces about any point, for the equilibrium of the body acted upon____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: cross sections of bronze and copper bars of equal lengt b c are their Ab and Ac are the respective stresses due to load P. If Pb and Pc are the loads shared by them, (where Eb and Ec are their modulii)____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: In the cable shown in the given figure, the minimum tension occurs at___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The locus of the end point of the resultant of the normal and tangential components of the stress on an inclined plane, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Co-efficient of wind resistance of a circular surface, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: static equations i.e. H V M = 0, to a determinate structure, we may By applying the determine_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The force in AD of the truss shown in given figure, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The area of the core of a column of cross sectional area A, is_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: In case of principal axes of a section________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 × 106 N/mm2, the depth of the joist, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If Q is load factor, S is shape factor and F is factor of safety in elastic design, the following_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A material is said to be perfectly elastic if__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If a concrete column 200 × 200 mm in cross-section is reinforced with four steel bars of 1200 mm2 total cross-sectional area. Calculate the safe load for the column if permissible stress in concrete is 5 N/mm2 and Es is 15 Ec________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The ratio of maximum and average shear stresses on a rectangular section, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of the section by_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The maximum bending moment for a simply supported beam with a uniformly distributed load w/unit length, is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The force in AC of the truss shown in the given figure, is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
