Theory of Structures Mcqs

Q.  The ratio of maximum shear stress to average shear stress of a circular beam, is________________?

a. 2/3
b. 3/2
c. 3/4
d. 4/3


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  The shape factor of standard rolled beam section varies from_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Principal planes are subjected to_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A rolled steel joist is simply supported at its ends and carries a uniformly distributed load which causes a maximum deflection of 10 mm and slope at the ends of 0.002 radian. The length of the joist will be________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (f /N)s__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The eccentricity (e) of a hollow circular column, external diameter 25 cm, internal diameter 15 cm for an eccentric load 100 t for non-development of tension, is__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In the truss shown in given figure, the force in member BD is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The moment of inertia of a circular section about any diameter D, is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick up the correct statement from the following__________.?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Y are the bending moment, moment of inertia, radius of curvature, modulus of If M, I, R, E, F, and elasticity stress and the depth of the neutral axis at section, then________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The locus of the moment of inertia about inclined axes to the principal axis, is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A steel plate d × b is sandwiched rigidly between two timber joists each D × B/2 in section. The steel will be (where Young’s modulus of steel is m times that of the timber)_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The general expression for the B.M. of a beam of length l is the beam carries M = (wl/2) x – (wx²/2)_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In the truss, the force in the member AC is_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The point of contraflexure is the point where_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  d constant, the width of a cantilever of length l of uniform strength loaded with Keeping the depth a uniformly distributed load w varies from zero at the free end and________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  y/n) (1 – a l/r), is For calculating the allowable stress of long columns. The empirical formula 0 known as_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For determining the support reactions at A and B of a three hinged arch, points B and Care joined and produced to intersect the load line at D and a line parallel to the load line through A at D’. Distances AD, DD’ and AD’ when measured were 4 cm, 3 cm and 5 cm respectively. The angle between the reactions at A and B is___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of the maximum deflections of a simply supported beam with a central load W and of a cantilever of same length and with a load W at its free end, is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A square column carries a load P at the centroid of one of the quarters of the square. If a is the side of the main square, the combined bending stress will be________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A material may fail if______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts