Process Equipment & Plant Design Mcqs for Chemical


Q.  The practical representative values of HETP for a number of commercial operations lies within a range of ______________ metre?

a. 0.1-0.2
b. 0.2-0.5
c. 0.4-0.9
d. 1.2-1.5


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  The type of stress developed in a metallic bar on subjecting it to a change in temperature without allowing it to be deformed is ______________ stress?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Reflux ratio variation in a distillation column is between___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Liquid/petroleum fuel storage tanks are built underground (as in case of petrol pumps), when the storage capacity is less than ______________ kilolitres?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  In a heat exchanger, shell side fluid velocity can be changed by changing the tube _______________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Steam side heat transfer co-efficient for design consideration under ordinary condition can be assumed to be about _____________ kcal/hr.m2.°C?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The safe distance of habitation from a hazardous chemical plant (TLV of its product < 1000 ppm) should be about ______________ kms?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  In case of a shell and tube heat exchanger, the effect of L/D on inside film heat transfer coefficient (hi) vanishes after a Reynold number of_____________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  (Le/D) for fully open globe value may be around__________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The value of fouling factor depends upon the__________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The operating pressure drop range in a bag filter is about ______________ mm water gauge?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Which of the following lengths of heat exchanger tubes are normally not used in practice ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  In packed absorption tower, onset of flooding usually occurs at a pressure drop of about ______________ mm of water column per metre height of packing?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Diameter of bubble caps used in high pressure columns is ______________ as compared to that used in identical vacuum columns?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Shell side heat transfer co-efficient in case of square pitch as compared to the triangular pitch under similar condition of fluid flow and tube size is_____________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  A riveted joint does not fail by _____________________ of rivets?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  In a shell and tube heat exchanger, the ‘tube pitch’ is defined as the _____________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  25 per cent cut segmental baffle means that the baffle__________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  For a cylindrical vessel of moderate height, the weld joint efficiency for joints parallel to the cylindrical axis is given as 1.0; while for joints along the girth (circumference) it is given as 0.8. In calculating the shell wall thickness using code formula for an internally pressurised cylindrical vessel, what value of weld joint efficiency should be used ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Of the pressure vessels, with same thickness but different diameters, which one withstands higher pressure ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Generally, as the length of the liquid path on a tray is increased beyond 5 ft, the overall column efficiency___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm