Applied Mechanics & Graphic Statics Mcqs


Q.  The pole distance is measured in___________________?

a. The pole distance is measured in___________________?
b. force scale
c. mass scale
d. time scale


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  The dimensions of power are_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The ratio of unit of force in gravitational system to that in absolute system is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A quantity measured in the C.G.S system of units has dimensions M”2L3 T3/2. What numerical factor would be required to convert the quantity to SI units ?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The dimensions of Gravitational Universal constant ‘G’ are______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  One Newton is equivalent to_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The potential energy of a particle falling through a straight shaft drilled through the earth (assumed homogenous and spherical) is proportional to____________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  At the instantaneous center, the velocity of the moving lamina at any instant is_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Which of the following represents the state of neutral equilibrium ?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  One end of an elastic string of natural length / and modulus X is kept fixed while to the other end is attached a particle of mass m which is hanging freely under gravity. The particle is pulled down vertically through a distance x, held at rest and then released. The motion is___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A simple pendulum of length / has an energy E, when its amplitude is A. If the length of pendulum is doubled, the energy will be___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the kinetic energy and potential energy of a simple harmonic oscillator of amplitude A are both equal to half the total energy, then the displacement is equal to_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  It is observed that in a certain sinusoidal oscillation, the amplitude is linearly dependent on the frequency f. If the maximum velocity during the oscillation is V, then V must be proportional to_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A particle of mass 2 kg executes simple harmonic motion of frequency 6/71 Hz and amplitude 0.25 m. Its maximum kinetic energy is___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If A is the amplitude of particle executing simple harmonic motion, then the total energy E of the particle is___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A stone is thrown up a slope of inclination 60° to the horizontal. At what angle to the slope must the stone be thrown so as to land as far as possible from the point of projection ?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If a projectile is fired with an initial velocity of 10 m/sec at an angle of 60° to the horizontal, its horizontal and vertical velocity at the highest point of trajectory are___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A projectile has maximum range of 40 m on a horizontal plane. If angle of projection is a and the time of flight is 1 second, then sin a must be about__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The maximum value of the horizontal range for a projectile projected with a velocity of 98 m/sec is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  For a given velocity of a projectile, the range is maximum when the angle of projection is___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  When a circular wheel rolls on a straight track, then the shape of body centrode and space centrode respectively are________________?
Category: Civil Engineering Mcqs,   Published by: teswesm