Design of Masonry Structures Mcqs

Q.  The mode of failure of a very short masonry member having h/t ratio of less than 4 is by _______________?

a. shear
b. vertical tensile splitting
c. buckling
d. any of the above


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  Rich cement mortars are more liable to cracking as compared to lean mortars because rich mortars have________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Water retentivity for brick masonry should not be less than__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For earthquake resistant masonry buildings, where seismic coefficient is less than 0.08, the horizontal distance between two openings shall not be less than_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Assertion A : Lime based mortars give higher ratio of brickwork strength to mortar strength as compared to non-lime mortar. Reason R : Lime based mortars have lower bond strength as compared to non-lime mortars? Select your answer according to the codes given below.
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Minimum thickness of stiffening wall for 1 to 3 storeys shall not be less than_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Assertion A : From consideration of structural soundness and economy of design, most codes control the maximum slenderness ratio of masonry walls and columns. Reason R : By controlling the maximum slenderness ratio, failure is by excessive stress and not by buckling.? Select your answer according to codes given below.
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For designing masonry components of a structure, seismic forces provision in the design calculation is not necessary for buildings constructed in________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Full restraint is provided by__________________? i) foundation footing of a wall ii) timber floor spanning on the wall and anchored to the wall iii) RCC slab with a minimum bearing of 10 cm on the wall select the correct statment.
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The bending stress in a wall or column subjected to effective vertical load need not be considered, if the eccentricity ratio is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the horizontal cross-sectional area of a wall is 1200 cm2, then the basic stress shall be multiplied by a reduction factor equal to________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If H is the height of wall between centers of supports, then the effective height of wall where concrete floors have a bearing on wall irrespective of the direction of span will be________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Where a structural component or a system is providing lateral support to five or more walls or columns, the lateral load to be resisted may be taken as_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the ratio of center to center spacing of intersecting walls to actual thickness of intersecting wall is more than 20, then the stiffening coefficient for wall proper will be_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Assertion A : For eccentricity ratio exceeding 1/6, effective thickness of masonry will get reduced. Reason R : For eccentricity ratio exceeding 1/6, there will be tension on one side of the member? Select your answer according to the codes give below.
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Maximum slenderness ratio of load bearing walls for a dwelling having more than 2 storeys________________? i) shall not exceed 12 if lime mortar is used ii) shall not exceed 18 if cement lime mortar 1:2:9 is used iii) shall not exceed 24 if cement mortar 1:6 is used the correct statments is ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Consider the following statements? 1. Masonry in rich cement mortar though having good strength with high shrinkage is much liable for surface cracks. 2. Lime mortar possesses poor workability and poor water retentivity and also suffers high shrinkage. 3. Masonry in lime mortar has better resistance against rain penetration and is less liable to crack when compared to masonry in cement mortar. Which of these statements are correct?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A good blast with a good yield is obtained if the cut hole is___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Drifters can be used to drill_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The correct sequence of drilling equipment for increasing size of holes in tunnels is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In compressed air tunneling, the volume of free air provided is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts