MCQs: In the zone of R.C.C. beam where shear stress is less than 5 kg/cm2, nominal reinforcement is provided at a pitch of________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: High strength concrete is used in prestressed member________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: on a circular slab of radius , the maximum radial moment at the centre of the If is the load slab, is WR²/16_____________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: If the permissible compressive and tensile stresses in a singly reinforced beam are 50 kg/cm2 and 1400 kg/cm2 respectively and the modular ratio is 18, the percentage area At of the steel required for an economic section, is__________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: The modular ratio m of a concrete whose permissible compressive stress is C, may be obtained from the equation.
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: Enlarged head of a supporting column of a flat slab is technically known as______________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: If A is the area of the foundation of a retaining wall carrying a load W and retaining earth of weight w per unit volume, the minimum depth (h) of the foundation from the free surface of the earth, is )/(1 + sin )]_________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: Thickened part of a flat slab over its supporting column, is technically known as_____________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: The pitch of the main bars in a simply supported slab, should not exceed its effective depth by_____________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: If is the sectional area of a prestressed rectangular beam provided with a tendon pre stressed by a force through its centroidal longitudinal axis, the compressive stress in concrete, is_______________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: Side face reinforcement shall be provided in the beam when depth of the web in a beam exceeds_____________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: The minimum head room over a stair must be_______________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: If q is the punching shear resistance per unit area a, is the side of a square footing for a column of side b, carrying a weight W including the weight of the footing, the depth D. of the footing from punching shear consideration, is____________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: If the length of a combined footing for two columns l metres apart is L and the projection on the left side of the exterior column is x, then the projection y on the right side of the exterior column, in order to have a uniformly distributed load, is (where is the distance of centre of gravity of column loads______________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: If the tendon is placed at an rectangular beam (sectional top edge)________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: The Young’s modulus of elasticity of steel, is__________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: Spacing of stirrups in a rectangular beam, is__________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: Total pressure on the vertical face of a retaining wall of height h acts parallel to free surface and from the base at a distance of_____________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: For initial estimate for a beam design, the width is assumed__________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts

MCQs: A prestressed rectangular beam which carries two concentrated loads W at L/3 from either end, is provided with a bent tendon with tension P such that central onethird portion of the tendon remains parallel to the longitudinal axis, the maximum dip h is_____________________?
Category: Civil Engineering Mcqs, Published by: TCode Scripts
