Applied Mechanics & Graphic Statics Mcqs


Q.  The member forces in a statically in determinate truss____________________?

a. can be obtained by graphic statics
b. cannot be obtained by graphic statics
c. may be obtained by graphic statics
d. can be obtained by graphic statics by trial and error


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  The ratio of unit of force in gravitational system to that in absolute system is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A quantity measured in the C.G.S system of units has dimensions M”2L3 T3/2. What numerical factor would be required to convert the quantity to SI units ?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The dimensions of Gravitational Universal constant ‘G’ are______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  One Newton is equivalent to_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The potential energy of a particle falling through a straight shaft drilled through the earth (assumed homogenous and spherical) is proportional to____________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  At the instantaneous center, the velocity of the moving lamina at any instant is_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Which of the following represents the state of neutral equilibrium ?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  One end of an elastic string of natural length / and modulus X is kept fixed while to the other end is attached a particle of mass m which is hanging freely under gravity. The particle is pulled down vertically through a distance x, held at rest and then released. The motion is___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A simple pendulum of length / has an energy E, when its amplitude is A. If the length of pendulum is doubled, the energy will be___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the kinetic energy and potential energy of a simple harmonic oscillator of amplitude A are both equal to half the total energy, then the displacement is equal to_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  It is observed that in a certain sinusoidal oscillation, the amplitude is linearly dependent on the frequency f. If the maximum velocity during the oscillation is V, then V must be proportional to_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A particle of mass 2 kg executes simple harmonic motion of frequency 6/71 Hz and amplitude 0.25 m. Its maximum kinetic energy is___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If A is the amplitude of particle executing simple harmonic motion, then the total energy E of the particle is___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A stone is thrown up a slope of inclination 60° to the horizontal. At what angle to the slope must the stone be thrown so as to land as far as possible from the point of projection ?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If a projectile is fired with an initial velocity of 10 m/sec at an angle of 60° to the horizontal, its horizontal and vertical velocity at the highest point of trajectory are___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A projectile has maximum range of 40 m on a horizontal plane. If angle of projection is a and the time of flight is 1 second, then sin a must be about__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The maximum value of the horizontal range for a projectile projected with a velocity of 98 m/sec is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  For a given velocity of a projectile, the range is maximum when the angle of projection is___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  When a circular wheel rolls on a straight track, then the shape of body centrode and space centrode respectively are________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The angular speed of a car while taking a circular turn of radius 100m at 36 km/hour, is_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm