# RCC Structures Design Mcqs

Q.  The maximum shear stress (q) in concrete of a reinforced cement concrete beam is_____________?

a. Shear force/(Lever arm × Width)
b. Lever arm/(Shear force × Width)
c. Width/(Lever arm × Shear force)
d. (Shear force × Width)/Lever arm

ANSWER: See Answer

No explanation is available for this question!
 MCQs:  Post tensioning system_______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  A foundation is called shallow if its depth, is________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  A flat slab is supported_______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  A pre-stressed concrete member__________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  [A + (m – 1)ASC] known as equivalent concrete area of R.C.C. is given by______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  If permissible working stresses in steel and concrete are respectively 1400 kg/cm2 and 80 kg/cm2 and modular ratio is 18, in a beam reinforced in tension side and of width 30 cm and having effective depth 46 cm, the lever arms of the section, is______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The maximum ratio of span to depth of a cantilever slab, is_______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  carrying a uniformly distributed load per metre length is suspended at the A pile of length centre and from other two points 0.15 L from either end ; the maximum hogging moment will be_______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The design of a retaining wall assumes that the retained earth________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The advantage of a concrete pile over a timber pile, is_______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  For stairs spanning horizontally, the minimum waist provided is________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The horizontal portion of a step in a stairs case, is known as_________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  A foundation rests on_______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  An R.C.C. roof slab is designed as a two way slab if________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is__________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  Piles are usually driven by________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  In a combined footing for two columns carrying unequal loads, the maximum hogging bending moment occurs at Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The live load to be considered for an inaccessible roof, is______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span of a square flat slab, should not be less than________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  If a bent tendon is required to balance a concentrated load W at the centre of the span L, the central dip h must be at least________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts