RCC Structures Design Mcqs


Q.  The load stress of a section can be reduced by______________?

a. Decreasing the lever arm
b. Increasing the total perimeter of bars
c. Replacing larger bars by greater number of small bars
d. Replacing smaller bars by greater number of greater bars


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Top bars are extended to the projecting parts of the combined footing of two columns Ldistance apart for a distance of_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  is the pre- stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If C is creep coefficient, f is original pre-stress in concrete, m is modular ratio, E is Young’s modulus of steel and e is shrinkage strain, the combined effect of creep and shrinkage is________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  An R.C.C. lintel is spanning an opening of 2 m span in a brick wall. The height of the roof is 2.9 m above the floor level and that of the opening is 2.1 m above the floor level. The lintel is to be designed for self weight plus_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The minimum clear cover for R.C.C. columns shall be_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The design of heel slab of a retaining wall is based on the maximum bending moment due to______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The neutral axis of a T-beam exists_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The minimum thickness of a flat slab is taken_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  An R.C.C beam of 25 cm width has a clear span of 5 metres and carries a U.D.L. of 2000 kg/m inclusive of its self weight. If the lever arm of the section is 45 cm., the beam is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A pre-cast pile generally used, is______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  In a pre-stressed member it is advisable to use________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Steel bars are generally connected together to get greater length than the standard length by providing_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  mutually perpendicular principal stresses acting on a soil mass, the normal stress If p1 and p2 are________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  carrying a uniformly distributed load per metre length is suspended at two A pile of length points, the maximum, B.M. at the centre of the pile or at the points of suspension, is_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If is the uniformly distributed load on a circular slab of radius maximum positive radial moment at its centre, is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the ratio of the span to the overall depth does not exceed 10, the stiffness of the beam will ordinarily be satisfactory in case of a__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  For M 150 grade concrete (1:2:4) the moment of resistance factor is_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The spacing of transverse reinforcement of column is decided by the following consideration_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The self-weight of the footing, is_____________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the bearing capacity of soil is 10 tonnes/cm2 and the projection of plain concrete footing from walls, is a cm, the depth D of footing is_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm