Chemical Engineering Basics Mcqs

Q.  The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge) ?

a. x1.5
b. x0.8
c. x-1.5
d. x-0.8


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  L.D. (Linz-Donawitz) converter is used in the production of____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  More than 95% of _______________ is present in corundum ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For dynamic strain measurement, the Wheatstone bridge used is of ______________ type ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A metal having a Poisson’s ratio = 0.3 is elastically deformed under uniaxial tension. If the longitudinal strain = 0.8, then the magnitude of thickness strain is________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  _________________ is not used as a material of construction in thermocouples ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A material being tested for endurance strength is subjected to the _____________ load?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Otto cycle used in spark ignition petrol engines is also known as the constant ________________ cycle?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  “Encyclopaedia of Chemical Technology” has been ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Optical activity is a/an _______________________ property ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  High endurance limit of carburised machine parts is because of the fact that carburisation __________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Function of fusible plug in a boiler is to ______________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the________________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Nickel is a _________________ material?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following are made out of the carbon steel having carbon content of 0.9 to 1%?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  An approximately _____________ process exemplifies the flow of a gas through a very long pipe of uniform cross-section ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The stress at which extension of the material takes place more rapidly as compared to the increase in load is termed as the _____________ point of the material?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick out the wrong conversion of absolute & kinematic viscosities ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following has the highest modulus of elasticity (about 7 × 106 kg/cm2) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  ____________ is the process used for setting up compressive stresses in the surface of a metal to improve its fatigue strength ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts