Theory of Structures Mcqs

Q.  The horizontal deflection of a parabolic curved beam of span 10 m and rise 3 m when loaded with a uniformly distributed load l t per horizontal length is (where Ic is the M.I. at the crown, which varies as the slope of the arch)___________________?

a. 50/EIc
b. 100/EIc
c. 150/EIc
d. 200/EIc


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  section modulus of a square section of side B and that of a circular section of The ratio of the diameter D, is___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The radius of gyration of a rectangular section (depth D, width B) from a centroidal axis parallel to the width is__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  a uniform circular bar of diameter d and length , which extends by an The deflection of amount under a tensile pull , when it carries the same load at its mid-span, is___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The equivalent length of a column of length L having one end fixed and the other end free, is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The equivalent length is of a column of length having both the ends fixed, is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the bar, is___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The maximum deflection of a simply supported beam of span L, carrying an isolated load at the centre of the span; flexural rigidity being EI, is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a shaft, the shear stress is not directly proportional to_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Beams composed of more than one material, rigidly connected together so as to behave as one piece, are known as________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Shear strain energy theory for the failure of a material at elastic limit, is due to_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The S.F. diagram of a loaded beam shown in the given figure is that of________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  P = /4L² is the equation of Euler’s crippling load, if__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2 MN/mm2, the tensile force developed at a temperature of 50°C, is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  H V are the algebraic sums of the forces resolved horizontally and vertically respectively, M is the algebraic sum of the moments of forces about any point, for the equilibrium of the body acted upon____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  cross sections of bronze and copper bars of equal lengt b c are their Ab and Ac are the respective stresses due to load P. If Pb and Pc are the loads shared by them, (where Eb and Ec are their modulii)____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In the cable shown in the given figure, the minimum tension occurs at___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The locus of the end point of the resultant of the normal and tangential components of the stress on an inclined plane, is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Co-efficient of wind resistance of a circular surface, is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  static equations i.e. H V M = 0, to a determinate structure, we may By applying the determine_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The force in AD of the truss shown in given figure, is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts