Railway Engineering Mcqs

Q.  The formation width for a double line Broad Gauge track in cutting (excluding drains) as adopted on Indian Railways is___________________?

a. 6.10 m
b. 8.84 m
c. 10.21m
d. 10.82 m


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  In a B.G. railway track, the specified ruling gradent is 1 in 250. The horizontal curve of 3° on a gradient of 1 in 250 will have the permissible gradient of__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If ‘A’ is the angle formed by two gauge faces, the crossing number will be____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the thickness of thinnest outside plate is 10 mm, then the maximum pitch of rivets in tension will be taken as______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  When the axis of load lies in the plane of rivet group, then the rivets are subjected to________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Bending compressive and tensile stresses respectively are calculated based on_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  When the axis of load lies in the plane of rivet group, then the most heavily loaded rivet will be the one which________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The difference between gross diameter and nominal diameter for the rivets up to 25 mm diameter is__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the thickness of plate to be connected by a rivet is 16 mm, then suitable size of rivet as per Unwin’s formula will be__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The heaviest I-section for same depth is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following types of riveted joint is free from bending stresses ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a gusseted base, when the end of the column is machined for complete bearing on the base plate, then the axial load is assumed to be transferred to base plate__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  By providing sufficient edge distance, which of the following failures of riveted joint can be avoided ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As compared to field rivets, the shop rivets are________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Efficiency of a riveted joint, having the minimum pitch as per IS : 800, is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Bolts are most suitable to carry_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  When the bolts are subjected to reversal of stresses, the most suitable type of bolt is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The effective length of a fillet weld should not be less than___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A butt weld is specified by__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The slenderness ratio of a column supported throughout its length by a masonry wall is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The effective length of a battened strut effectively held in position at both ends but not restrained in direction is taken as________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts