Engineering Economy Mcqs

Q.  The financial health of the company is measured in terms of______________?

a. Liquidity
b. Solvency
c. Relative risk
d. All of the above


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  The basic stress in masonry units having height to width ratio of 1.5 may be increased by a factor of_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For strengthening a 50 m long and 5 m high straight compound wall built in brick work, which one of the following would be most suitable?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Assertion A : For identical strength, a composite cement-lime mortar is preferred over cement mortar. Reason R : Composite cement-lime mortar has higher drying shrinkage than cement mortar_____________? Select your answer based on the codes given below Codes?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For masonry built in 1:1:6 cement-lime-sand mix mortar or equivalent, the horizontal shear stress permissible on the area of a mortar bed joint is_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Consider the following statements regarding provision of chases in masonry_________________? (i) No chase should be permitted in a half brick load-bearing wall, (ii) Vertical chases should not be closer than 2 m in any stretch of a wall, (iii) Chases should be provided near to bearings of beams and lintels. Select the the statements ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Cement mortars richer than 1 : 3 are not used in masonry because_________________? i) there is no gain in strength of masonry ii) there is high shrinkage iii) they are prone to segregation select the correct statements?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A 200 mm thick brick masonry wall made of modular bricks carries an axial load of 30 kN/m from wall above and an eccentric load of 20 kN/m from RCC floor acting at a distance of 47.5 mm from the centre line of the wall. The resultant eccentricity ratio is A. B. C. D. ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Consider the following statements regarding bands to be provided for strengthening masonry work in masonry buildings constructed in zone III, IV and V? (i) Lintel band is provided at lintel level on partition walls, (ii) Gable band is provided at top of gable masonry below the purlins, (iii) The bands shall be to full width of the wall and not less than 7.5 cm in depth, (iv) The bands shall be made of reinforced concrete only. the correct statements are?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Rich cement mortars are more liable to cracking as compared to lean mortars because rich mortars have________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Water retentivity for brick masonry should not be less than__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For earthquake resistant masonry buildings, where seismic coefficient is less than 0.08, the horizontal distance between two openings shall not be less than_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Assertion A : Lime based mortars give higher ratio of brickwork strength to mortar strength as compared to non-lime mortar. Reason R : Lime based mortars have lower bond strength as compared to non-lime mortars? Select your answer according to the codes given below.
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Minimum thickness of stiffening wall for 1 to 3 storeys shall not be less than_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Assertion A : From consideration of structural soundness and economy of design, most codes control the maximum slenderness ratio of masonry walls and columns. Reason R : By controlling the maximum slenderness ratio, failure is by excessive stress and not by buckling.? Select your answer according to codes given below.
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For designing masonry components of a structure, seismic forces provision in the design calculation is not necessary for buildings constructed in________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Full restraint is provided by__________________? i) foundation footing of a wall ii) timber floor spanning on the wall and anchored to the wall iii) RCC slab with a minimum bearing of 10 cm on the wall select the correct statment.
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The bending stress in a wall or column subjected to effective vertical load need not be considered, if the eccentricity ratio is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the horizontal cross-sectional area of a wall is 1200 cm2, then the basic stress shall be multiplied by a reduction factor equal to________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If H is the height of wall between centers of supports, then the effective height of wall where concrete floors have a bearing on wall irrespective of the direction of span will be________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Where a structural component or a system is providing lateral support to five or more walls or columns, the lateral load to be resisted may be taken as_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts