Mechanical Operations Mcqs for Chemical

Q.  The filtrate flow rate in constant pressure filtration___________________?

a. Continuously increases
b. Continuously decreases
c. Remain constant throughout
d. May increase or decrease; depends on the pressure


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  What is the reduction ratio in a fine crushing operation having following feed and product sizes ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  _____________ is the most suitable for compounding rubber and plastic solids ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  During filtration operation, the filtrate encounters the resistance of the ___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Rittinger number which designates the new surface produced per unit of mechanical energy absorbed by the material being crushed, depends on the ______________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Size measurement of ultrafine particles can be best expressed in terms of___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following achieves the least reduction ratio for a given feed size ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As particle size is reduced__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Reciprocal of sphericity is termed as the________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Filtration of water in a paper mill is done by a/an _______________ filter?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  With increase in the capacity of screens, the screen effectiveness__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As per Taggart’s formula, the capacity (kg/hr) of Jaw & Gyratory crushers (for gapes of 10 to 60 cms) is equal to (where, L = Length of feed opening, cms S = Maximum width of discharge opening, cms) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  To get a fine talc powder from its granules, the equipment used is____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The controlling resistance in a rotary drum vacuum filter is the ________________ resistance?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Separation of particles of various sizes, shapes and densities by allowing them to settle in a fluid is called__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Theoretical capacity of crushing rolls in tons/hr is given by (where, V = peripheral velocity, m/sec. W = width of rolls, m Dr = distance between rolls ρ = density of material to be crushed, kg/m3 here, V =πND where, N = speed of the rolls in rotation per second (rps) D = diameter of rolls, m) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a size reduction crushing operation, the feed size is 10 to 50 mm, while the product size is 2 to 10 mm. This is a case of _______________ crushing?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A fluid energy mill is used for __________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Reciprocating screens are normally inclined at an angle of 5° with the horizontal and employ gyratory motion at feed end & reciprocating motion at the discharge end. They are not suitable for the screening of the ___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Gravity stamp mill is meant for the ___________________ crushing?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For spheres, the surface shape factor is given by (where, A = area, V = volume, and D = diameter) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts