Estimating & Costing Mcqs


Q.  The expected out turn of half brick partition wall per mason per day is___________________?

a. 1.5 m 3
b. 2.0 m3
c. 4.0 m2
d. 5.0 m2


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  A very comfortable type of stairs is_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The width of the flange of a L-beam, should be less than______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2, the beam________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Columns may be made of plain concrete if their unsupported lengths do not exceed their least lateral dimension_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A pre-stressed concrete member is preferred because___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If is the net upward pressure on a square footing of side for a square column of side , the maximum bending moment is given by_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  To ensure uniform pressure distribution, the thickness of the foundation, is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  longitudinal bars and lateral stirrups, is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Pick up the incorrect statement from the following: Tensile reinforcement bars of a rectangular beam_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The maximum permissible size of aggregates to be used in casting the ribs of a slab, is______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Top bars are extended to the projecting parts of the combined footing of two columns Ldistance apart for a distance of_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  is the pre- stressed force applied to tendon of a rectangular pre-stressed beam whose area of cross section is and sectional modulus is . The minimum stress on the beam subjected to a maximum bending moment is________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If C is creep coefficient, f is original pre-stress in concrete, m is modular ratio, E is Young’s modulus of steel and e is shrinkage strain, the combined effect of creep and shrinkage is________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  An R.C.C. lintel is spanning an opening of 2 m span in a brick wall. The height of the roof is 2.9 m above the floor level and that of the opening is 2.1 m above the floor level. The lintel is to be designed for self weight plus_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The minimum clear cover for R.C.C. columns shall be_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The design of heel slab of a retaining wall is based on the maximum bending moment due to______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The neutral axis of a T-beam exists_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The minimum thickness of a flat slab is taken_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  An R.C.C beam of 25 cm width has a clear span of 5 metres and carries a U.D.L. of 2000 kg/m inclusive of its self weight. If the lever arm of the section is 45 cm., the beam is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm