Design of Steel Structures Mcqs

Q.  The effective length of a battened column is increased by_________________?

a. 5%
b. 10%
c. 15%
d. 20%


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  The effect of racking forces is considered in the design of_________________? i) lateral braces ii) chord members The correct answer is
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The sway bracing is designed to transfer____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The bracing provided in the plane of end posts is called__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The least dimension in case of a circular column of diameter D is taken as_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In case of timber structures, the simple bending formula M = fz may be applied for________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The mechanism method and the statical method give__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Shape factor is a property which depends________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The mechanism method of plastic analysis satisfies___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of plastic section modulus to elastic section modulus__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following conditions is to be satisfied both in elastic and plastic analysis ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As per IS:800, in the plastic design, which of the following pairs are correctly matched? Working Loads Load factor________________? (i) Dead load 1.7 (ii) Dead Load + imposed load 1.7 (iii) Dead load + load due to wind or 1.3 seismic forces (iv) Dead load + imposed load + load 1.7 due to wind or seismic forces Of these statements
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In case of plastic design, the calculated maximum shear capacity of a beam as per IS:800 shall be________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The moment of inertia of the pair of vertical stiffeners about the center line of the web should not be less than__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For a compression member with double angle section, which of the following section will give larger value of minimum radius of gyration?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A steel beam supporting loads from the floor slab as well as from wall is termed as________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Hudson’s formula gives the dead weight of a truss bridge as a function of_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The allowable shear stress in the web of mild steel beams decreases with__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pitch of tacking rivets, when double angles connected back to back and acting as tension members should not be more than_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In moment resistant connections, the moment resistance of riveted connection depends upon________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For rivets in tension with counter-sunk heads, the tensile value shall be____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts