Dock & Harbor Engineering Mcqs

Q.  The difference in height between highest high water and lowest low water is called_______________?

a. mean range
b. maximum range
c. maximum rise
d. mean rise


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  The length of runway under standard conditions is 2000 m. The elevation of airport site is 300 m. Its reference temperature is 33.05°C. If the runway is to be constructed with an effective gradient of 0.25 percent, the corrected runway length will be________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Zero fuel weight of an aircraft is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As per ICAO, for airports serving big aircrafts, the crosswind component should not exceed_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For determining the basic runway.length, the landing case requires that aircraft should come to a stop within p % of the landing distance. The value of p is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Runway threshold is indicated by a series of parallel lines starting from a distance of_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In Intrumental landing system, the middle markers are located___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The centre to centre spacing of heliport lighting along the periphery of landing and take off area should be______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Assertion A: The width of a taxiway is smaller than the runway width. Reason R : The speed of the aircraft on a taxiway is greater than that on runway.? Select your answer based on coding system given below
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As per UK design criteria, if LCN of aircraft is between 1.25 to 1.5 times the LCN of pavement, then the number of movements allowed are__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The slope of the transitional surface for A, B and C type of runway shall be_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In approach areas of runways equipped with instrumental landing facilities any object within 4.5 km distance from runway end shall be considered as an obstruction if its height is more than______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The main disadvantage of angle nose out parking configuration of aircraft is that the_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following factors are taken into account for estimating the runway length required for aircraft landing ? 1. Normal maximum temperature 2. Airport elevation 3. Maximum landing weight 4. Effective runway gradient Select the correct answer using the codes given below Codes?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The runway length after correcting for elevation and temperature is 2845 m. If the effective gradient on runway is 0.5 percent then the revised runway length will be_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In an airport, if 4 groups of 5 gates each located well-separated are considered for traffic and the future to present traffic ratio is 3, then the total requirement of future gates will be______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Consider the following statements: Wind rose diagram is used for the purposes of_________________? 1. runway orientation 2. estimating the runway capacity 3. geometric design of holding apron select the correct answer?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Castor angle is defined as the angle______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Maximum gross take-off weight of an aircraft is__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following is used for servicing and repairs of the aircraft ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following is an example of failure in flexible pavements ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts