Process Equipment & Plant Design Mcqs for Chemical

Q.  The diameter of a propeller agitator used in agitation tank ranges from ____________ percent of the tank diameter and its peripheral speed is normally 300 to 500 metres/minute ?

a. 5 to 10
b. 15 to 30
c. 40 to 50
d. 55 to 75


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  The shell side pressure drop in a shell and tube heat exchanger is maximum for _______________ baffle?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Equivalent diameter for heat transfer calculation for a duct of square cross-section having each side as ‘d’ will be__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Friction factor for turbulent flow in a new pipe is given by____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  To keep the power input constant for a stirred vessel operating under fully developed turbulent flow conditions (constant power number), if the impeller diameter is increased by 20%, the impeller speed should be decreased by a factor of_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Triangular pitch tube layout as compared to square pitch in a shell and tube heat exchanger________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Smaller sized packings are generally dumped to the packed columns, and the large ones of size greater than ______________ mm are stacked individually, which provides better control over bed porosity and offers lower gas pressure drop?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ends of a cylindrical vessel can be closed by a head, which can be one of the four shapes. For the same thickness, choose the one which can withstand the highest pressure ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A stuffing box is used for____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of shear stress to shear strain is called ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In case of a shell and tube heat exchanger, the minimum shell thickness for carbon steel (inclusive of corrosion allowance) depends on shell diameter and is in the range of ________________ mm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  _____________________ tray arrangement is recommended for distillation column having diameter upto 4 ft ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In case of bubble cap distillation column of diameter greater than 1.2 metres, the cap diameter is roughly about _______________ cms?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Wall thickness of schedule 40 pipe as compared to that of schedule 80 pipe is ___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Speed of the drum of the rotary vacuum filter normally ranges from _____________ rpm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a continuous distillation column, the optimum reflux ratio ranges from _______________ times the minimum reflux ratio?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The type of stress developed in a metallic bar on subjecting it to a change in temperature without allowing it to be deformed is ______________ stress?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Reflux ratio variation in a distillation column is between___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Liquid/petroleum fuel storage tanks are built underground (as in case of petrol pumps), when the storage capacity is less than ______________ kilolitres?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a heat exchanger, shell side fluid velocity can be changed by changing the tube _______________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Steam side heat transfer co-efficient for design consideration under ordinary condition can be assumed to be about _____________ kcal/hr.m2.°C?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts