Railway Engineering Mcqs


Q.  The desirable rate of change of cant deficiency in case of Metre Gauge is_______________?

a. 20 mm/sec
b. 35 mm/sec
c. 55 mm/sec
d. 65 mm/sec


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Tensile strength of steel used in rails should not be less than____________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The cross-sectional area of 52 kg flat footed rail is_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Largest percentage of material in the rail is in its__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The standard length of rail for Broad Gauge and Meter Gauge are respectively __________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The rail is designated by its__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Two important constituents in the com-position of steel used for rail are_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The following tests are conducted for rails _________________? i) falling weight test ii) tensile test iii) hammer test The compulsory tests are?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Which of the following factors govern the choice of the gauge ? i) volume and nature of traffic ii) speed of train iii) physical features of the country The correct answer is ?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The formation width for a railway track depends on the_________________? i) type of gauge ii) number of tracks to be laid side by side iii) slope of sides of embankment or cutting The correct answer is?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Study the following statements regarding creep_________________? i) Creep is greater on curves than on tangent railway track ii) Creep in new rails is more than that in old rails iii) Creep is more on steep gradients than on level track The correct answer is?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Switch angle depends on______________? i) heel divergence ii) length of tongue rail iii) flangeway clearance iv) throw of switch The correct answer is?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  In a scissors cross-over, the crossings provided are_________________? i) 2 obtuse angle crossings ii) 4 obtuse angle crossings iii) 4 acute angle crossings iv) 6 acute angle crossings The correct answer is ?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The reception signal is__________________? i) outer signal ii) home signal iii) starter iv) advanced starter The correct answer is?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  To ensure exact gauge, the gauge tie plates are provided at_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  In a B.G. railway track, the specified ruling gradent is 1 in 250. The horizontal curve of 3° on a gradient of 1 in 250 will have the permissible gradient of__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If ‘A’ is the angle formed by two gauge faces, the crossing number will be____________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the thickness of thinnest outside plate is 10 mm, then the maximum pitch of rivets in tension will be taken as______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  When the axis of load lies in the plane of rivet group, then the rivets are subjected to________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Bending compressive and tensile stresses respectively are calculated based on_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  When the axis of load lies in the plane of rivet group, then the most heavily loaded rivet will be the one which________________?
Category: Civil Engineering Mcqs,   Published by: teswesm