MCQs: _______________ mill is not used for grinding wheat into flour and for milling of cereals & other ?
vegetable products.
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: The energy required per unit mass to grind limestone particles of very large size to 100 μm is 12.7 kWh/ton. An estimate (using Bond’s law) of the energy to grind the particles from a very large size to 50 μm is________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: What is the critical rotation speed in revolutions per second, for a ball mill of 1.2 m diameter charged with 70 mm dia balls ?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: According to Taggart’s rule for selecting between a gyratory crusher and a jaw crusher; the later should be used, if the hourly tonnage to be crushed divided by the square of the gape expressed in cm is less than_______________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: Wet sieving is employed, when the product contains ________________ materials?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: Size reduction mechanism used in Jaw crushers is__________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: Solid particles separation based on the difference in their flow velocities through fluids is termed as the__________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: The mechanism of size reduction by a hammer mill is by impact and attrition between the________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: Pebble mills are tumbling mills widely used for grinding in the manufacture of paints & pigments and cosmetic industries, where iron contamination in the product is highly objectionable. Pebbles used in pebble mill are made of__________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: During size reduction by a jaw crusher, the energy consumed decreases with the__________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: Out of the following size reduction equipments, the maximum feed size can be accepted by the__________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: The capacity of a classifier in ‘tons of solid/hr’ is given by (where, A = cross-sectional area in m2, V = rising velocity of fluid in m/sec, S = percentage of solids in the suspension by volume, ρ = density of solids in kg/m3)_________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: For a turbine agitated and baffled tank, operating at low Reynold’s number (based on impeller diameter), the power number (Np) varies with NRe as_________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: Short distance transportation of grain, gravel, sand, ash, asphalt etc. is done by using a ______________ conveyor?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: Screen efficiency is______________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: In case of a hammer crusher ?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: To remove very small amount of tiny solid impurities from liquid, we use a_____________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: _____________________ baffles are provided in ball mills ?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: Crushing efficiency of a machine ranges between __________________ percent?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
MCQs: Rod mills employed for grinding_________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|