|
MCQs: In plastic analysis, the shape factor for rectangular section, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A masonry dam (density = 20,000 N/m3) 6 m high, one metre wide at the top and 4 m wide at the base, has vertical water face. The minimum stress at the base of the dam when the reservoir is full, will be_______________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A shaft rotating N.R.M. under a torque T, transmits a power_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The maximum deflection due to a load W at the free end of a cantilever of length L and having flexural rigidity EI, is_____________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The ratio of the length and depth of a simply supported rectangular beam which experiences maximum bending stress equal to tensile stress, due to same load at its mid span, is_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The force in EC of the truss shown in the given figure, is__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If and are external and internal diameters of a circular shaft respectively, its polar moment of inertia, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: length of a column of length L, having one end fixed and other end hinged, is The equivalent_____________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A lift of weight W is lifted by a rope with an acceleration f. If the area of cross-section of the rope is A, the stress in the rope is_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: parabolic arch of span and rise , is given by The equation of a________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A rectangular column shown in the given figure carries a load P having eccentricities ex and ey along X and Y axes. The stress at any point (x, y) is_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A simply supported beam carries a varying load from zero at one end and w at the other end. If the length of the beam is a, the shear force will be zero at a distance x from least loaded point where x is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The shape factor of standard rolled beam section varies from_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Principal planes are subjected to_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A rolled steel joist is simply supported at its ends and carries a uniformly distributed load which causes a maximum deflection of 10 mm and slope at the ends of 0.002 radian. The length of the joist will be________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (f /N)s__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The eccentricity (e) of a hollow circular column, external diameter 25 cm, internal diameter 15 cm for an eccentric load 100 t for non-development of tension, is__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: In the truss shown in given figure, the force in member BD is______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The moment of inertia of a circular section about any diameter D, is______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Pick up the correct statement from the following__________.?
Category: Civil Engineering Mcqs, Published by: teswesm
|
