Railway Engineering Mcqs

Q.  Study the following statements regarding creep_________________?
i) Creep is greater on curves than on tangent railway track
ii) Creep in new rails is more than that in old rails
iii) Creep is more on steep gradients than on level track
The correct answer is?


a. only (i)
b. (i)and(ii)
c. (ii) and (iii)
d. (i), (ii) and (iii)


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  The effective length of a fillet weld should not be less than___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A butt weld is specified by__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The slenderness ratio of a column supported throughout its length by a masonry wall is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The effective length of a battened strut effectively held in position at both ends but not restrained in direction is taken as________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  According to IS Specifications, the maximum pitch of rivets in compression is_____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The maximum slenderness ratio of a steel column, the design of which is governed by wind or seismic forces is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  According to IS:800, in the Merchant Rankine formula the value of imperfection index (n) is_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The maximum slenderness ratio of a compression member carrying both dead and superimposed load is___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  According to IS Specifications, the effective length of a column effectively held in position at both ends and restrained in direction at one end is taken as________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The actual thickness of butt weld as compared to the thickness of plate is usually________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For a standard 45° fillet, the ratio of size of fillet to throat thickness is_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A circular column section is generally not used in actual practice because________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The best arrangement to provide unified behaviour in built up steel columns is by______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The use of tie plates in laced columns is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Angle of inclination of the lacing bar with the longitudinal axis of the column should preferably be between____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The effective length of a battened column is increased by_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The slenderness ratio of lacing bars should not exceed________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Shear buckling of web in a plate girder is prevented by using________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Minimum thickness of web in a plate girder, when the plate is accessible and also exposed to weather, is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As per IS : 800, for compression flange, the outstand of flange plates should not exceed________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts