Process Equipment & Plant Design Mcqs for Chemical

Q.  Steam is preferred to be used as a heating medium in heat exchangers, because of its_________________?

a. Low cost
b. High latent heat
c. Non-corrosive condensate
d. High film co-efficient


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  Height equivalent to a theoretical plate (HETP) is the height of packing that will give the same separation as one theoretical plate in gas-liquid mass transfer operations like distillation, absorption/stripping and humidification/dehumidification. HETP which is experimentally determined, depends upon the_______________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Liquid gradient over the tray results due to the___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of tube length to shell diameter in case of liquid shell and tube heat exchanger ranges from__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The slope of the feed line in distillation operation is given by (where, q = fraction of the feed stream that is liquid ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  ____________ head is the most economical for cylindrical vessels designed for operating at high pressure (> 15 atm.)?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The testing pressure of storage tanks and pressure vessels designed as per Indian standard codes should be about ______________ times the design pressure?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following factors affect the pressure drop in a co-current gas-liquid absorption packed tower ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following packing materials provides for maximum mass transfer ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The absorption factor is defined as (where, S1 = slope of the equilibrium curve, S2 = slope of the operating line) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a shell and tube heat exchanger, tube side _______________ of the mass velocity?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In sieve plate column, holes are drilled or punched in sizes ranging from 2.5 to 12 mm (5 mm being widely used). The hole pitch is normally ______________ times the hole diameter to give the required hole area?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  “A claming section” before the liquid flows into the downcomer is provided to__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  With increase in pressure drop (for a given particle size), the dust collection efficiency of a cyclone separator will________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Most of the storage vessels/tanks are made cylindrical, because of the fact that a cylinder _________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Apex angle of conical heads used in the bottom heads of chemical process equipments is usually__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Length to diameter ratio of most rotary driers is in the range of____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For identical situation, condensing film coefficient in case of a horizontal condenser is almost ______________ the value expected in case of vertical condenser?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The difficulty of liquid distribution in packed towers is accentuated, when the ratio of tower diameter to packing diameter is_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Cooling water fouling factors vary in the range of 0.001 to 0.003____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which tube arrangement in a heat exchanger would facilitate highest heat transfer rate ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts