Process Equipment & Plant Design Mcqs for Chemical

Q.  Steam economy is defined as the amount of evaporation per unit amount of steam used, while the capacity is the total evaporation obtained per hour. Use of multiple effects in evaporation ?

a. Increases capacity
b. Increases economy
c. Does not affect the capacity
d. Both B. & C.


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  At the following point for a given packing and set of fluids, the pressure drop per metre of packed height, with variation in fluid rates and operating pressure____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a double pipe (concentric) heat exchanger, the hydraulic radius for heat transfer (for a fluid flowing through the annulus) would be_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A/an _______________ is used for changing the direction of a pipeline?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Low pressure steam (with saturation temperature between 105 to 120°C) is usually used in the vacuum evaporators, which normally employ a vacuum of about _______________ mm Hg (referred to a 760 mm mercury barometer)?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Elastic failure of a material occurs, when the tensile stress equals yield strength, yield point or the elastic limit. Also, the elastic failure occurs according to maximum strain theory, when the maximum tensile strain equals (where, ζ = yield strength and E = modulus of elasticity) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A ‘rupture disc’ is provided in chemical equipments as an accessory meant for ___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The minimum shell thickness for tank ≤ 15 metres diameter is limited to _______________ mm, for reasons of elastic stability?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  _____________ shaped roof is the most commonly used roof for cylindrical storage tanks?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Filtration rate is affected by the________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Normally, the length to diameter ratio of rotary dryers varies from 4 to 10 and for its economic operation; the number of transfer units (NTU) for such dryers varies from ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick out the wrong statement ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of volumes of the mixed reactor to the plug flow reactor (for identical feed composition, flow rate, conversion, and for all positive reaction orders) is always ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a _____________ riveted joint, the number of rivets decreases from the innermost row to the outermost row?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A binary liquid Azeotropic mixture has boiling point lower than either of the components, when it shows _____________ deviation from Raoult’s Law?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The clearance between two tubes in a shell and tube heat exchanger is known as ‘ligament’, whose minimum value is _____________ the outside diameter of the tube, but in no case it should be less than 4.5 mm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following is the most common type of baffle used in industrial shell and tube heat exchanger ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  ____________ is the determining factor for the number of bubble caps to be used per tray?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The buckling tendency of compression members is always in the direction of the _____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The equivalent diameter for fluid flow through a channel of constant non-circular cross section of area ‘A’ is given by (where, P = perimeter of the channel in contact with the fluid) ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Accidents in chemical plants are mostly due to___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts