Railway Engineering Mcqs

Q.  Standard size of wooden sleeper for Broad Gauge track is____________________?

a. 275x25x13cm
b. 180x20x11.5 cm
c. 225x23x13 cm
d. 250x26x12 cm


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  The formation width for a railway track depends on the_________________? i) type of gauge ii) number of tracks to be laid side by side iii) slope of sides of embankment or cutting The correct answer is?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Study the following statements regarding creep_________________? i) Creep is greater on curves than on tangent railway track ii) Creep in new rails is more than that in old rails iii) Creep is more on steep gradients than on level track The correct answer is?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Switch angle depends on______________? i) heel divergence ii) length of tongue rail iii) flangeway clearance iv) throw of switch The correct answer is?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a scissors cross-over, the crossings provided are_________________? i) 2 obtuse angle crossings ii) 4 obtuse angle crossings iii) 4 acute angle crossings iv) 6 acute angle crossings The correct answer is ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The reception signal is__________________? i) outer signal ii) home signal iii) starter iv) advanced starter The correct answer is?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  To ensure exact gauge, the gauge tie plates are provided at_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a B.G. railway track, the specified ruling gradent is 1 in 250. The horizontal curve of 3° on a gradient of 1 in 250 will have the permissible gradient of__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If ‘A’ is the angle formed by two gauge faces, the crossing number will be____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the thickness of thinnest outside plate is 10 mm, then the maximum pitch of rivets in tension will be taken as______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  When the axis of load lies in the plane of rivet group, then the rivets are subjected to________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Bending compressive and tensile stresses respectively are calculated based on_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  When the axis of load lies in the plane of rivet group, then the most heavily loaded rivet will be the one which________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The difference between gross diameter and nominal diameter for the rivets up to 25 mm diameter is__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the thickness of plate to be connected by a rivet is 16 mm, then suitable size of rivet as per Unwin’s formula will be__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The heaviest I-section for same depth is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following types of riveted joint is free from bending stresses ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a gusseted base, when the end of the column is machined for complete bearing on the base plate, then the axial load is assumed to be transferred to base plate__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  By providing sufficient edge distance, which of the following failures of riveted joint can be avoided ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As compared to field rivets, the shop rivets are________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Efficiency of a riveted joint, having the minimum pitch as per IS : 800, is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts